LiftMaster 8550W 8550W Owners Manual - Page 35

Remote Control, To Add, Reprogram, Or Change A Remote Control/keyless Entry Pinusing The Door Control - homelink

Get LiftMaster 8550W PDF manuals and user guides View all LiftMaster 8550W manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Operation Remote Control Your remote control has been programmed at the factory to operate with your garage door opener. Up to 40 Security+ 2.0® remote controls can be programmed to the garage door opener. Older LiftMaster remote controls are NOT compatible, see page 40 for compatible accessories. Programming can be done through the door control or the learn button the garage door opener. To program additional accessories refer to the instructions provided with the accessory or visit LiftMaster.com. If your vehicle is equipped with a Homelink®, you may require an external adapter depending on the make, model, and year of your vehicle. Visit www.homelink.com for additional information. TO ADD, REPROGRAM, OR CHANGE A REMOTE CONTROL/KEYLESS ENTRY PIN USING THE DOOR CONTROL 1. Press the navigation button below "MENU" to view the Features menu. 2. Use the navigation buttons to scroll to "PROGRAM". 3. Select "REMOTE" or "KEYPAD" to program from the program menu. 4. Remote Control: Press the button on the remote control that you wish to operate your garage door. Keyless Entry: Enter a 4-digit personal identification number (PIN) of your choice on the keyless entry keypad. Then press the ENTER button. The garage door opener lights will flash (or two clicks will be heard) when the code has been programmed. Repeat the steps above for programming additional remote controls or keyless entry devices. If programming is unsuccessful, program the remote using the learn button. 1 2 Press to continue. 3 Press to continue. TO REMOTE PROGRAM USING THE LEARN BUTTON ON THE GARAGE DOOR OPENER 1. Press and release the LEARN Button on the garage door opener. 2. Press the button on the remote control. 1 2 "click" "click" LEARN Button LEARN LED To Erase the Memory ERASE ALL REMOTE CONTROLS AND KEYLESS ENTRIES 1. Press and hold the learn button on garage door opener until the learn LED goes out (approximately 6 seconds). All remote control and keyless entry codes are now erased. Reprogram any accessory you wish to use. ERASE ALL DEVICES (Including MyQ® enabled accessories) 1. Press and hold the learn button on garage door opener until the learn LED goes out (approximately 6 seconds). 2. Immediately press and hold the learn button again until the learn LED goes out. All codes are now erased. Reprogram any accessory you wish to use. ERASE THE Wi-Fi NETWORK FROM THE GARAGE DOOR OPENER Press and hold the black adjustment button until 3 beeps are heard (approximately 6 seconds). ERASE A MyQ® ACCOUNT Go to myLiftMaster.com to delete your MyQ account. 4 OR 4GHI 5JKL 6 MNO 7 8 9 PRS TUV WXY * * 0 QZ # 0 QZ # ENTER ENTER ???? PIN LEARN Button Black Adjustment Button 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
35
Operation
Remote Control
Your remote control has been programmed at the factory to operate with your
garage door opener.
Up to 40 Security+ 2.0
®
remote controls can be programmed to the garage door opener.
Older LiftMaster remote controls are NOT compatible, see page 40 for compatible
accessories. Programming can be done through the door control or the learn button the
garage door opener. To program additional accessories refer to the instructions provided
with the accessory or visit LiftMaster.com. If your vehicle is equipped with a Homelink
®
,
you may require an external adapter depending on the make, model, and year of your
vehicle. Visit www.homelink.com for additional information.
TO ADD, REPROGRAM, OR CHANGE A REMOTE CONTROL/KEYLESS ENTRY PIN
USING THE DOOR CONTROL
1.
Press the navigation button below "MENU" to view the Features menu.
2.
Use the navigation buttons to scroll to "PROGRAM".
3.
Select "REMOTE" or "KEYPAD" to program from the program menu.
4.
Remote Control:
Press the button on the remote control that you wish to operate
your garage door.
Keyless Entry:
Enter a 4-digit personal identification number (PIN) of your choice
on the keyless entry keypad. Then press the ENTER button.
The garage door opener lights will flash (or two clicks will be heard) when the code has
been programmed. Repeat the steps above for programming additional remote controls
or keyless entry devices. If programming is unsuccessful, program the remote using the
learn button.
Press
to continue.
TO REMOTE
Press
to continue.
1
2
3
OR
PIN
?
?
?
?
4
5
7
8
9
0
*
#
ENTER
0
QZ
*
#
ENTER
6
4
PROGRAM USING THE LEARN BUTTON ON THE GARAGE DOOR OPENER
1.
Press and release the LEARN Button on the garage door opener.
2.
Press the button on the remote control.
LEARN LED
LEARN
Button
“click”
“click”
1
2
To Erase the Memory
ERASE ALL REMOTE CONTROLS AND KEYLESS ENTRIES
1.
Press and hold the learn button on garage door opener until the learn LED goes
out (approximately 6 seconds). All remote control and keyless entry codes are
now erased.
Reprogram any accessory you wish to use.
ERASE ALL DEVICES (Including MyQ
®
enabled accessories)
1.
Press and hold the learn button on garage door opener until the learn LED goes
out (approximately 6 seconds).
2.
Immediately press and hold the learn button again until the learn LED goes out.
All codes are now erased.
Reprogram any accessory you wish to use.
ERASE THE Wi-Fi NETWORK FROM THE GARAGE DOOR OPENER
Press and hold the black adjustment button until 3 beeps are heard (approximately 6
seconds).
ERASE A MyQ
®
ACCOUNT
Go to myLiftMaster.com to delete your MyQ account.
LEARN Button
Black Adjustment Button