Konica Minolta AccurioPress C6085 AccurioPress C6100/C6085 AccurioPress C3080/ - Page 71

If an Out-of-Range Image is Detected, Status, Cause, Remedy, The message Too Many

Get Konica Minolta AccurioPress C6085 PDF manuals and user guides View all Konica Minolta AccurioPress C6085 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

8.1 If an Out-of-Range Image is Detected 8 No. Status Cause Remedy 5 Message "alignment er- The system failed in An alignment failure may occur on a ror" is displayed on the alignment between the pale image or a simple image of ruled bookmark of the out-of- reference image and the lines only. range image report. inspection image. When this error recurs on a specific im- age, set the entire target page to an ex- cluding area in [Inspection Excluding Area]. For details, refer to "6. Automatic In- spection Area" in this manual. A large stain is found on an image. If any stain is found on the reference image, create a reference image again. If any stain is found on printouts, perform automatic inspection again after carrying out maintenance of this machine. The printed image is completely different from the reference image. Check whether the print job matches the reference image. If no problems are identified, create a reference image again. 6 The message "Too Many One hundred or more Stains may be seen in the paper feed- Stains" is displayed on stains, which is in the ing route. Perform maintenance for this the bookmark of the out- standard, were detected. machine. of-range image report. (Such stains are not out For details, refer to [Perform mainte- of range, so a comment nance] or [Adjustments] in the HTML marked by a red circle is User's Guide. not displayed.) 7 Message "Inspection The paper size is differ- Check whether the print job matches failed" is displayed on ent between the refer- the reference image. If no problems are the control panel. ence image and the print identified, create a reference image job. again. Automatic Inspection Operation Manual 8-3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
Automatic Inspection Operation Manual
8-3
8.1
If an Out-of-Range Image is Detected
8
5
Message "alignment er-
ror" is displayed on the
bookmark of the out-of-
range image report.
The system failed in
alignment between the
reference image and the
inspection image.
An alignment failure may occur on a
pale image or a simple image of ruled
lines only.
When this error recurs on a specific im-
age, set the entire target page to an ex-
cluding area in [Inspection Excluding
Area].
For details, refer to "6. Automatic In-
spection Area" in this manual.
A large stain is found on
an image.
If any stain is found on the reference
image, create a reference image again.
If any stain is found on printouts, per-
form automatic inspection again after
carrying out maintenance of this ma-
chine.
The printed image is
completely different from
the reference image.
Check whether the print job matches
the reference image. If no problems are
identified, create a reference image
again.
6
The message "Too Many
Stains" is displayed on
the bookmark of the out-
of-range image report.
One hundred or more
stains, which is in the
standard, were detected.
(Such stains are not out
of range, so a comment
marked by a red circle is
not displayed.)
Stains may be seen in the paper feed-
ing route. Perform maintenance for this
machine.
For details, refer to [Perform mainte-
nance] or [Adjustments] in the HTML
User's Guide.
7
Message "Inspection
failed" is displayed on
the control panel.
The paper size is differ-
ent between the refer-
ence image and the print
job.
Check whether the print job matches
the reference image. If no problems are
identified, create a reference image
again.
No.
Status
Cause
Remedy