Kenwood KMM-104AY Instruction Manual - Page 14

AUDIO SETTINGS While listening to any source... 1 Press AUD to enter [AUDIO CONTROL] directly. 2 Turn the volume knob to select an item (see the following table), then press the knob. 3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit. To return to the previous setting item, press . Default: XX AUDIO CONTROL SUB-W LEVEL -15 to +15 (0) Adjusts the subwoofer output level. BASS LEVEL MID LEVEL TRE LEVEL -8 to +8 (+2) -8 to +8 (+1) -8 to +8 (+1) Adjusts the level to memorize for each source. (Before making an adjustment, select the source you want to adjust.) EQ PRO (This setting is stored to [USER].) BASS ADJUST BASS CTR FRQ 60/80/100/200 or 60HZ/80HZ/100HZ/200HZ: Selects the center frequency. BASS LEVEL -8 to +8 (+2): Adjusts the level. BASS Q FACTOR 1.00/1.25/1.50/2.00: Adjusts the quality factor. BASS EXTEND ON: Turns on the extended bass. ; OFF: Cancels. MID ADJUST MID CTR FRQ 0.5KHZ/1.0KHZ/1.5KHZ/2.5KHZ: Selects the center frequency. MID LEVEL -8 to +8 (+1): Adjusts the level. MID Q FACTOR 0.75/1.00/1.25: Adjusts the quality factor. TRE ADJUST TRE CTR FRQ 10.0KHZ/12.5KHZ/15.0KHZ/17.5KHZ: Selects the center frequency. TRE LEVEL -8 to +8 (+1): Adjusts the level. PRESET EQ DRIVE EQ/TOP40/POWERFUL/ROCK/POPS/EASY/JAZZ/NATURAL/ USER: Selects a preset equalizer suitable to the music genre. (Select [USER] to use the settings made in [EQ PRO].) [DRIVE EQ] is a preset equalizer that reduces noise outside the car or running noise of the tyres. BASS BOOST LV1/LV2/LV3 or LEVEL1/LEVEL2/LEVEL3: Selects your preferred bass boost level. ; OFF: Cancels. LOUDNESS LV1/LV2 or LEVEL1/LEVEL2: Selects your preferred low and high frequencies boost to produce a well-balanced sound at a low volume level. ; OFF: Cancels. SUBWOOFER SET ON: Turns on the subwoofer output. ; OFF: Cancels. LPF SUBWOOFER THROUGH: All signals are sent to the subwoofer. ; 85HZ/120HZ/160HZ: Audio signals with frequencies lower than 85 Hz/120 Hz/160 Hz are sent to the subwoofer. SUB-W PHASE REVERSE (180°)/NORMAL (0°): Selects the phase of the subwoofer output to be in line with the speaker output for optimum performance. (Selectable only if a setting other than [THROUGH] is selected for [LPF SUBWOOFER].) FADER BALANCE VOLUME OFFSET R15 to F15 (0): Adjusts the rear and front speaker output balance. L15 to R15 (0): Adjusts the left and right speaker output balance. For AUX: -8 to +8 (0) ; For other sources: -8 to 0: Preset the initial volume level of each source. (Before adjustment, select the source you want to adjust.) SOUND RECNSTR ON: Creates realistic sound by compensating the high-frequency (Sound components and restoring the rise-time of the waveform that are lost in reconstruction) audio data compression. ; OFF: Cancels. • [SUB-W LEVEL]/[SUBWOOFER SET]/[LPF SUBWOOFER]/[SUB-W PHASE] is selectable only if [SWITCH PREOUT] is set to [SUB-W] or [SUBWOOFER]. ( 4) • [SUB-W LEVEL]/[LPF SUBWOOFER]/[SUB-W PHASE] is selectable only if [SUBWOOFER SET] is set to [ON]. 10 ENGLISH