Home » Invacare Manuals » Wheelchairs » Invacare MYONADLT » Manual Viewer

Invacare MYONADLT Owners Manual - Page 66

Caution, Warning

Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

9 TROUBLESHOOTING AND MAINTENANCE ƽ CAUTION As with any vehicle, the wheels and tires should be checked periodically for cracks and wear, and should be replaced if damaged. 5. The wheels, casters, and tires should be checked periodically for cracks and wear, and should be replaced when necessary. Contact a qualified technician or Invacare customer support at the telephone numbers on the back of this manual. 6. Periodically adjust wheel locks in correlation to tire wear. Refer to Adjusting Anti-Tippers on page 104.  Tire wear is excessive if: • Pneumatic Tires - there is missing tread or the tires are bald. • Urethane Tires - there are cuts, surface defects or the tires are loose on the rims. • Rubber Tires - 30% or more of the tire has worn away. Invacare recommends that rear wheel tire/tube and caster tire/tube be replaced every five years. 7. Regularly check for loose spokes in the rear wheels. If loose, have them adjusted. Contact a qualified technician or Invacare customer support at the telephone numbers on the back of this manual. 8. Periodically check handrims to ensure they are secured to the rear wheels. Refer to Replacing Handrims on page 96. ® 9. Periodically check caster wheel bearings to make sure they are clean and free from moisture. Use a Teflon lubricant if necessary. ƽ WARNING When cleaning rear cane or hand grip areas use only a clean towel lightly dampened with cool water. Verify that grips are dry prior to use. Use of soap or ammonia based cleaning solutions will result in the hand grips sliding off the cane assembly. Failure to observe this warning may result in injury to the user or bystanders. 10. Hand grips should be checked monthly for wear/looseness/deterioration. Clean if desired. Replace if looseness or deterioration is found. 11. On a monthly basis, for the 80° and 90° front riggings, check the mounting pin for excessive wear or damage. Replace mounting pin if worn or damaged. 12. Inspect front rigging mounting pin and hardware. Specifically, inspect the mounting screw that secures the mounting pin to the front rigging. Tighten if mounting screw is loose. Invacare® MyOn™MyOn Jr Wheelchairs 66 Part No 1167418

Section	Page
© 2013 Invacare Corporation. All rights reserved. Republication, duplication or modification in whole or in part is prohibited without prior written permission from Invacare. Trademarks are identified by ™ and ®. All trademarks are owned by or li...	2
WD-40 is a registered trademark of the WD-40 Company.	2
Teflon is a registered trademark of E.I. Du Pont De Nemours and Company.	2
3-in-1 oil is a registered trademark of American Home Products Corporation.	2
1 General 7	3
Symbols 7	3
Limited Warranty 8	3
2 Safety 9	3
General Guidelines 9	3
3 Overview 15	3
Label Locations 15	3
Component Identification 17	3
Typical Product Parameters 18	3
4 Safety/Handling of Wheelchairs 24	3
Safety/Handling of Wheelchairs 24	3
Stability and Balance 24	3
Coping with Everyday Obstacles 25	3
A Note to Wheelchair Assistants 25	3
Tipping 25	3
Stairways 27	3
Escalators 28	3
Transferring To and From Other Seats 29	3
Percentage of Weight Distribution 30	3
Reaching, Leaning and Bending - Forward 31	3
Reaching, Bending - Backward 31	3
5 Safety Inspection 32	3
Safety Inspection Checklists 32	3
6 Wheelchair Operation 36	3
Unfolding and Folding Wheelchair 36	4
Securing the Optional Push Handle 38	4
Placing the Optional Push Handle in the Storage Position 41	4
Using Wheel Locks 42	4
Folding Wheel Lock Handles 43	4
Installing/Removing Front Riggings 44	4
Installing/Removing Elevating Legrests 47	4
Raising/Lowering the Elevating Legrest 50	4
Using Flipback Armrest. 51	4
7 Transport Ready Option 53	4
About Transport Ready Packages 54	4
Compliance Information 55	4
Specifications 55	4
Securing the Wheelchair to the Vehicle 56	4
Securing the Occupant 58	4
Maintenance and Adjustment Sections 63	4
9 Troubleshooting and Maintenance 64	4
Troubleshooting 64	4
Maintenance 65	4
Transporting the Wheelchair 67	4
10 Front Riggings 68	4
Adjusting Footrest Height 68	4
Replacing Heel Loop Strap 69	4
Installing Impact Guards/Calf Strap 70	4
Adjusting Elevating Legrest Calfpad Height and Depth 70	4
Replacing Mounting Pin on 80° and 90° Front Rigging 71	5
Installing Adjustable Angle Flip-Up Footplate Hinge 72	5
Adjusting Adjustable Angle Flip-Up Footplates 73	5
11 Arms 75	5
Removing/Installing and Adjusting T-Arms 75	5
Removing/Installing Flipback Armrests 77	5
Adjusting the Height and Depth of the Flip Back Arms 78	5
Replacing Armrest Arm Pad 79	5
Installing the Optional Swingaway Padded Armrest Socket Assembly 79	5
Adjusting Swingaway Padded Armrest Height 81	5
Using the Locking Cantilever Arms 82	5
Removing/Installing Locking Cantilever Arms 82	5
Adjusting Locking Cantilever Arm Height 83	5
12 Seat/Back 84	5
Removing/Installing the Back 84	5
Removing/Installing Seat Upholstery 86	5
Removing/Installing Standard Back Upholstery. 87	5
Adjustable Back Upholstery 87	5
Installing/Replacing Adjustable Back Upholstery 88	5
Adjusting the Height Adjustable Back 90	5
Adjusting the Back Angle 91	5
Removing/Installing the Seat Positioning Strap 92	5
Installing/Removing the Spreader Bar 92	5
13 Rear Wheels/Front Casters 93	5
Removing/Installing Rear Wheels 93	5
Adjusting Quick-Release Axles 95	5
Replacing Handrims 96	6
Adjusting Forks 97	6
Removing/Installing the Caster Assemblies 98	6
Replacing the Sector Block 99	6
14 Wheel Locks 100	6
Adjusting Wheel Locks 100	6
Replacing Wheel Lock Handle. 102	6
15 Anti-tippers 103	6
Installing Anti-Tippers 103	6
Adjusting Anti-Tippers 104	6
1 General	7
1.1 Symbols	7
Warnings	7
Signal words are used in this manual and apply to hazards or unsafe practices which could result in personal injury or property damage. See the information below for definitions of the signal words.	7
m	7
Warning	7
Warning indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.	7
m	7
caution	7
Caution indicates a potentially hazardous situation which, if not avoided, may result in property damage or minor injury or both.	7
i	7
Gives useful tips, recommendations and information for efficient, trouble-free use.	7
1.2 Limited Warranty	8
PLEASE NOTE: THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW APPLICABLE TO PRODUCTS MANUFACTURED AFTER JULY 4, 1975.	8
This warranty is extended only to the original purchaser/user of our products.	8
This warranty gives you specific legal rights and you may also have other legal rights which vary from state to state.	8
Invacare warrants its product to be free from defects in materials and workmanship for a period of one year from the date of purchase when purchased new and unused from Invacare or an authorized provider. The side frames and crossmembers are under a ...	8
For warranty service, please contact the dealer from whom you purchased your Invacare product. In the event you do not receive satisfactory warranty service, please write directly to Invacare at the address on the back cover. Provide dealer’s name,...	8
Limitations and Exclusions: The foregoing warranty shall not apply to serial numbered products if the serial number has been removed or defaced, products subjected to negligence, accident, improper operation, maintenance or storage, products modified...	8
THE FOREGOING EXPRESS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES WHATSOEVER, WHETHER EXPRESS OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABLITY AND FITNESS FOR A PARTICULAR PURPOSE, AND THE SOLE REMEDY FOR VIOLATIONS OF ANY...	8
THIS WARRANTY SHALL BE EXTENDED TO COMPLY WITH STATE/PROVINCIAL LAWS AND REQUIREMENTS.	8
i	11
When changes to the left hand column occur, follow across the chart and refer to the • procedure to maintain the proper stability, safety and handling of the wheelchair.	11
m	11
Warning	11
Stability Warning	11
The seat height, seat depth, back angle, seating system/upholstery, size/position of the rear wheels, size/position of the front casters, as well as the user condition directly relate to the stability of the wheelchair. Any change to one or any combi...	11
Seat-to-floor heights have specific positions depending on rear wheel size, rear wheel position, front caster size/position and seat-to-floor angle. These adjustments MUST be performed by a qualified technician.	11
seat height	11
seat depth	11
back angle	11
seating system/Upholstery	11
caster size	11
caster position	11
Rear wheel size	11
Rear wheel position	11
user condition	11
m	12
Warning	12
Repair and Service Information	12
Unless otherwise noted, all service and adjustments should be performed while the wheelchair is unoccupied.	12
Operating Information	12
To determine and establish your particular safety limits, practice bending, reaching and transferring activities in several combinations in the presence of a qualified healthcare professional before attempting active use of the wheelchair.	12
DO NOT attempt to reach objects if you have to move forward in the seat.	12
DO NOT attempt to reach objects if you have to pick them up from the floor by reaching down between your knees.	12
DO NOT lean over the top of the back upholstery to reach objects from behind as this may cause the wheelchair to tip over.	12
DO NOT shift your weight or sitting position toward the direction you are reaching as the wheelchair may tip over.	12
DO NOT tip the wheelchair without assistance.	12
DO NOT use an escalator to move a wheelchair between floors. Serious bodily injury may occur.	12
DO NOT operate on roads, streets or highways.	12
DO NOT climb, go up or down ramps or traverse slopes greater than 9°.	12
NEVER leave an unoccupied wheelchair on an incline.	12
DO NOT attempt to move up or down an incline with a water, ice or oil film.	12
DO NOT attempt to ride over curbs or obstacles. Doing so may cause your wheelchair to turn over and cause bodily harm or damage to the wheelchair.	12
m	13
Warning	13
Wheel locks are not brakes. DO NOT attempt to stop a moving wheelchair with the wheel locks	13
DO NOT attempt to lift the wheelchair by any removable (detachable) parts. Lifting by means of any removable (detachable) parts of a wheelchair may result in injury to the user or damage to the wheelchair.	13
NEVER try to lift or tip the wheelchair by cantilever arms or T- arms, serious injury can occur.	13
DO NOT overtighten hardware attaching to the frame. This could cause damage to the frame tubing.	13
DO NOT stand on the frame of the wheelchair.	13
DO NOT sit or transfer into the wheelchair unless it is fully open and the seat frame rails are fully seated into the side frame H-blocks.	13
Anti-tippers MUST BE attached at all times. Inasmuch as the anti-tippers are an option on this wheelchair (you may order with or without the anti-tippers), Invacare strongly recommends ordering the anti-tippers as an additional safeguard for the whee...	13
Unless otherwise noted, all service and adjustments should be performed while the wheelchair is unoccupied.	13
If wheelchair is exposed to extreme temperature (above 100°F or below 32°F), high humidity and/or becomes wet, prior to use, ensure handgrips DO NOT twist on wheelchair handle - otherwise damage or injury may occur.	13
ALWAYS use the handrims for self-propulsion. Inasmuch as the handrims are an option on this wheelchair (you may order with or without the handrims), Invacare strongly recommends ordering the handrims as an additional safeguard for the wheelchair user.	13
DO NOT use the footplate as a platform when getting in or out of the wheelchair.	13
ALWAYS keep hands and fingers clear of moving parts to avoid injury.	13
DO NOT place hand or fingers on the underside of the seat rail when opening or closing the wheelchair.	13
m	14
Warning	14
Seat Positioning Straps	14
ALWAYS wear your seat positioning strap. Inasmuch as the seat positioning strap is an option on this wheelchair (you may order with or without the seat positioning strap), Invacare strongly recommends ordering the seat positioning strap as an additio...	14
With regards to seat/chest positioning straps - it is the obligation of the DME dealer, therapists and other healthcare professionals to determine if a seat/chest positioning strap is required to ensure the safe operation of this equipment by the use...	14
Tire Pressure	14
DO NOT use your wheelchair unless it has the proper tire pressure (p.s.i.). DO NOT overinflate the tires. Failure to follow these suggestions may cause the tire to explode and cause bodily harm. The recommended tire pressure is listed on the side wal...	14
Replacement of a pneumatic tire or tube MUST be performed by a qualified technician.	14
Weight Training	14
Invacare does not recommend the use of its wheelchairs as a weight training apparatus. Invacare wheelchairs have not been designed or tested as a seat for any kind of weight training. If occupant uses said wheelchair as a weight training apparatus, I...	14
Weight Limitation	14
The wheelchair has a weight limitation of:	14
MyOn - 275 lbs (125 kgs)	14
Myon Jr - 165 lbs (75 kgs) with TRRO option; 175 lbs (85 kgs) without TRRO option	14
MyOn (Heavy Duty) - 350 lbs (159 kgs)	14
3 Overview	15
3.1 Label Locations	15
Serial Number	15
Label Location	15
Wheelchairs with Transport Ready Option	16
3.2 Component Identification	17
Seat Upholstery	17
3.3 Typical Product Parameters	18
Model Numbers:	18
MYONADLT	18
MYONTO	18
MYONTS	18
seat width:	18
oVERALL WIDTH:	18
Width of Folded Wheelchair:	18
seat Depth:	18
overall depth (with riggings):	18
Overall depth (without riggings):	19
overall height:	19
height of chair with backrest folded:	19
Seat To floor	19
Height from front of seat to floor:	19
Seat to Floor	19
Height from Back of Seat to floor:	19
back style:	19
back height:	20
i	20
* 0° Back cane angle.	20
**8° Back cane angle.	20
Adjustable Back Angle (Optional):	20
back upholstery style:	21
Arm styles:	21
front riggings:	21
Footplate:	21
rear axle:	21
Rear Wheels:	22
handrims:	22
Wheel locks:	22
caster options:	23
weight:	23
Weight Capacity:	23
shipping weight (approximate):	23
4 Safety/Handling of Wheelchairs	24
4.1 Safety/Handling of Wheelchairs	24
“Safety and Handling” of the wheelchair requires the close attention of the wheelchair user as well as the assistant. This manual points out the most common procedures and techniques involved in the safe operation and maintenance of the wheelchai...	24
Use this information only as a “basic” guide. The techniques that are discussed on the following pages have been used successfully by many.	24
Individual wheelchair users often develop skills to deal with daily living activities that may differ from those described in this manual. Invacare recognizes and encourages each individual to try what works best for him/her in overcoming architectur...	24
4.2 Stability and Balance	24
m	24
Warning	24
ALWAYS wear your seat positioning strap. Inasmuch as the seat positioning strap is an option on this wheelchair (you may order with or without the seat positioning strap), Invacare strongly recommends ordering the seat positioning strap as an additio...	24
DO NOT attempt to lift a wheelchair by lifting on any removable (detachable) parts. Lifting by means of any removable (detachable) parts of the wheelchair may result in injury to the user or damage to the wheelchair.	24
ALWAYS check hand grips for looseness before using the wheelchair. If loose and/or worn, replace IMMEDIATELY.	24
DO NOT climb, go up, or down ramps or traverse slopes greater than 9°.	24
Invacare strongly recommends proceeding down ramps or slopes slowly to avoid hard braking or sudden stops.	24
DO NOT leave elevating legrests in the fully extended position when proceeding down ramps or slopes.	24
Be aware that carrying heavy objects on your lap while occupying the wheelchair may adversely affect the stability of the wheelchair, resulting in serious bodily injury to the user, damage to the wheelchair and surrounding property.	24
m	25
Warning	25
This wheelchair has been designed to accommodate one individual. If more than one individual occupies the wheelchair this may adversely affect the stability of the wheelchair, resulting in serious bodily injury to the user and passenger and damage th...	25
To assure stability and proper operation of your wheelchair, you must at all times wear your seat positioning strap and maintain proper balance. Your wheelchair has been designed to remain upright and stable during normal daily activities as long as ...	25
Virtually all activities which involve movement in the wheelchair have an effect on the center of gravity. Invacare recommends using seat positioning straps for additional safety while involved in activities that shift your weight.	25
DO NOT lean forward out of the wheelchair any further than the length of the armrests. Make sure the casters are pointing in the forward position whenever you lean forward. This can be achieved by advancing the wheelchair and then reversing it in a s...	25
4.3 Coping with Everyday Obstacles	25
Coping with the irritation of everyday obstacles can be alleviated somewhat by learning how to manage your wheelchair. Keep in mind your center of gravity to maintain stability and balance.	25
4.4 A Note to Wheelchair Assistants	25
When assistance to the wheelchair user is required, remember to use good body mechanics. Keep your back straight and bend your knees whenever tilting the wheelchair or traversing curbs, or other impediments.	25
Also, be aware of detachable parts such as arms or legrests. These must NEVER be used to move the wheelchair or as lifting supports, as they may be inadvertently released, resulting in possible injury to the user and/or assistant(s).	25
When learning a new assistance technique, have an experienced assistant help you before attempting it alone.	25
4.5 Tipping	25
m	25
Warning	25
DO NOT tip the wheelchair without assistance.	25
When tipping the wheelchair, an assistant should grasp the back of the wheelchair on a non-removable (non-detachable) part. Inform the wheelchair occupant before tipping the wheelchair and remind him/her to lean back. Be sure the occupant’s feet an...	25
Tipping - Curbs	26
Method 1 - Wheelchair with Step Tubes	26
FIGURE 1 Method 1 - Wheelchair with Step Tubes	26
m	26
Warning	26
DO NOT let the wheelchair drop the last few inches to the ground. This could result in injury to the occupant.	26
Push the wheelchair forward until the rear wheels roll up and over the curb.	26
Method 2 - Wheelchair without Step Tubes	26
1. Unless the first assistant has exceptional upper body strength, it is recommended that METHOD 2 use two assistants.	26
FIGURE 2 Method 2 - Wheelchair without Step Tubes	26
4.6 Stairways	27
m	27
Warning	27
Extreme caution is advised when it is necessary to move an occupied or unoccupied wheelchair up or down the stairs. Invacare recommends that, if possible, the user be removed from the wheelchair prior to moving. Invacare recommends using two assistan...	27
Follow this procedure for moving the wheelchair between floors when an elevator is not available:	27
Moving Up Stairs	27
1. If necessary, rotate the anti-tippers so the wheels are facing up.	27
2. One assistant (positioned behind the wheelchair), securely grasps a non-removable (non-detachable) part of the wheelchair for leverage and tilts the wheelchair back to the balance point.	27
3. After the wheelchair has been tilted back to the balance point, the assistant behind the wheelchair backs the wheelchair up against the first step.	27
4. The second assistant (positioned in the front of the wheelchair), with a firm hold on a non-detachable part of the framework, lifts the wheelchair up and on to the next stair above and steadies the wheelchair as the assistant behind the wheelchair...	27
5. The wheelchair should not be lowered until the last stair has been negotiated and the wheelchair has been rolled away from the stairway.	27
6. If necessary, rotate the anti-tippers so the wheels are facing down.	27
Moving Down Stairs	27
1. If necessary, rotate the anti-tippers so the wheels are facing up.	27
2. One assistant (positioned behind the wheelchair), securely grasps a non-removable (non-detachable) part of the wheelchair for leverage and tilts the wheelchair back to the balance point.	27
3. After the wheelchair has been tilted back to the balance point, the assistant behind the wheelchair rolls the wheelchair up to the edge of the first step.	27
4. The second assistant (positioned in the front of the wheelchair), with a firm hold on a non-detachable part of the framework, lowers the wheelchair down and on to the next stair below and steadies the wheelchair as the assistant in the rear places...	28
5. The wheelchair should not be lowered until the last stair has been negotiated and the wheelchair has been rolled away from the stairway.	28
6. If necessary, rotate the anti-tippers so the wheels are facing down.	28
FIGURE 3 Stairways	28
4.7 Escalators	28
m	28
Warning	28
DO NOT use an escalator to move a wheelchair between floors. Serious bodily injury may occur.	28
4.8 Transferring To and From Other Seats	29
m	29
Warning	29
Before attempting to transfer in or out of the wheelchair, every precaution should be taken to reduce the gap distance. Align both casters parallel with the object you are transferring onto. Also be certain the wheel locks are engaged to help prevent...	29
warning	29
Engaging the wheel locks may not prevent the wheelchair from moving on all floor surfaces including those that may be wet or slick. Always exercise caution when transferring into or out of your wheelchair.	29
caution	29
When transferring, position yourself as far back as possible in the seat. This will prevent damaged upholstery and the possibility of the wheelchair tipping forward.	29
i	29
This activity may be performed independently provided you have adequate mobility and upper body strength.	29
1. Position the wheelchair as close as possible along side the seat to which you are transferring, with the front casters parallel to it.	29
2. Engage wheel locks and fold down the wheel lock handles.	29
3. Remove or flip back armrests.	29
4. Shift body weight into seat with transfer.	29
Maximum Gap Distance	29
FIGURE 4 Transferring To and From Other Seats	29
4.9 Percentage of Weight Distribution	30
m	30
Warning	30
DO NOT attempt to reach objects if you have to move forward in the seat or pick them up from the floor by reaching down between your knees.	30
The seat height, seat depth, back angle, seat system/upholstery, caster size/position, rear wheel size, rear wheel position, correct anti-tipper as well as the end user’s disability or end user’s physical condition and capabilities directly relat...	30
WHEELCHAIRS WITH TRRO ONLY - The center of gravity is factory set. DO NOT adjust the center of gravity - otherwise injury or damage may occur. Contact Invacare for service.	30
Many activities require the wheelchair owner to reach, bend and transfer in and out of the wheelchair. These movements will cause a change to the normal balance, the center of gravity, and the weight distribution of the wheelchair. To determine and e...	30
4.10 Reaching, Leaning and Bending - Forward	31
m	31
Warning	31
DO NOT attempt to reach objects if you have to move forward in the seat or pick them up from the floor by reaching down between your knees.	31
FIGURE 6 Reaching, Leaning and Bending - Forward	31
4.11 Reaching, Bending - Backward	31
m	31
Warning	31
DO NOT lean over the top of the back upholstery. This will change your center of gravity and may cause you to tip over.	31
Keep hands and fingers clear of moving parts to avoid injury.	31
FIGURE 7 Reaching, Bending - Backward	31
5 Safety Inspection	32
i	32
Twice a year, take your wheelchair to a qualified dealer for a thorough inspection and servicing. Regular cleaning will reveal loose or worn parts and enhance the smooth operation of your wheelchair. To operate properly and safely, your wheelchair mu...	32
5.1 Safety Inspection Checklists	32
Initial adjustments should be made to suit the personal body structure needs and preferences of the user. Thereafter follow these maintenance procedures:	32
Inspect/Adjust Initially	32
Wheelchair rolls straight (no excessive drag or pull to one side).	32
Ensure all hardware is tight.	32
All fasteners on clothing guards are secure.	32
Arms are secure but easy to release and adjustment levers engage properly.	32
Adjustable height arms operate and lock securely.	32
Armrest pad sits flush against arm tube.	32
Seat and/or back upholstery have no rips.	32
Inspect adjustable angle back attaching hardware is securely tightened.	32
Ensure hand grips are not loose.	32
Sealed bearings and axle nut tension are correct.	32
No excessive side movement or binding when rear wheels are lifted and spun.	32
Quick-release axles lock properly.	32
Inspect handrims for signs of rough edges or peeling finish.	32
Inspect for broken spokes.	32
Wheel/fork assembly has proper tension when caster is spun. Caster should come to a gradual stop.	33
m	33
caution	33
As with any vehicle, the wheels/casters and tires should be checked periodically for cracks, flat spots and wear, and should be replaced.	33
Loosen/tighten locknut if wheel wobbles noticeably or binds to a stop.	33
Wheel bearings are clean and free of moisture.	33
Ensure all caster/wheel/fork/headtube fasteners are secure.	33
Wheel locks do not interfere with tires when rolling.	33
Wheel lock pivot point are free of wear and looseness.	33
Wheel locks are easy to engage.	33
Inspect tires/casters for flat spots and wear.	33
Check pneumatic tires for proper inflation (recommended tire pressure is listed on the side wall of the tire).	33
m	33
caution	33
DO NOT use WD-40®, 3-in-1 Oil®, or other penetrating lubricants on quick-release axles. Otherwise, binding and/or damage to the wheelchair may occur.	33
Clean quick-release axles with a Teflon® lubricant.	33
Ensure axles are free from dirt, lint, etc.	33
Ensure roller bearings are free from dirt, lint, etc.	33
Adjust wheel locks as tires wear.	33
Clean and wax all parts.	33
Clean upholstery and armrests with mild soap and water.	33
Ensure casters are free of debris.	33
Clean upholstery and armrests with mild soap and water.	33
Check that all labels are present and legible. Replace if necessary.	33
Inspect/Adjust Weekly	34
Wheelchair rolls straight (no excessive drag or pull to one side).	34
Quick-release axles lock properly.	34
Inspect for broken spokes.	34
Wheel/fork assembly has proper tension when caster is spun. Caster should come to a gradual stop.	34
Inspect tires/casters for flat spots and wear.	34
Check pneumatic tires for proper inflation (recommended tire pressure is listed on the side wall of the tire).	34
Ensure casters are free of debris.	34
Inspect/Adjust Monthly	34
Inspect seat positioning strap for any signs of wear. Ensure buckle latches. Verify hardware that attaches strap to frame is secure and undamaged. Replace if necessary.	34
Loosen/tighten locknut if wheel wobbles noticeably or binds to a stop.	34
Wheel bearings are clean and free of moisture.	34
Wheel locks do not interfere with tires when rolling.	34
Wheel lock pivot point are free of wear and looseness.	34
Ensure all caster/wheel/fork/headtube fasteners are secure.	34
Ensure all hardware is tight.	34
Ensure hand grips are not loose.	34
Ensure casters are free of debris.	34
For 80° and 90° front riggings, check the mounting pin for excessive wear or damage. Replace mounting pin if worn or damaged.	34
Inspect front rigging mounting pin and hardware. Specifically, inspect the mounting screw that secures the mounting pin to the front rigging. Tighten mounting screw if loose.	34
Inspect/Adjust Periodically	34
Wheelchair rolls straight (no excessive drag or pull to one side).	34
Arms are secure but easy to release and adjustment levers engage properly.	34
Adjustable height arms operate and lock securely.	35
Armrest pad sits flush against arm tube.	35
All fasteners on clothing guards are secure.	35
Seat and/or back upholstery have no rips.	35
Inspect adjustable angle back attaching hardware is securely tightened.	35
No excessive side movement or binding when rear wheels are lifted and spun.	35
Inspect handrims for signs of rough edges or peeling finish.	35
Inspect tires/casters for flat spots and wear.	35
Check pneumatic tires for proper inflation (recommended tire pressure is listed on the side wall of the tire).	35
Wheel lock pivot point are free of wear and looseness.	35
Clean upholstery and armrests with mild soap and water.	35
Sealed bearings and axle nut tension are correct.	35
Wheel/fork assembly has proper tension when caster is spun. Caster should come to a gradual stop.	35
Loosen/tighten locknut if wheel wobbles noticeably or binds to a stop.	35
Wheel bearings are clean and free of moisture.	35
Wheel locks are easy to engage.	35
Clean quick-release axles with a Teflon lubricant.	35
Ensure axles are free from dirt, lint, etc.	35
Ensure roller bearings are free from dirt, lint, etc.	35
Adjust wheel locks as tires wear.	35
Clean and wax all parts.	35
Ensure casters are free of debris.	35
Clean upholstery and armrests with mild soap and water.	35
Check that all labels are present and legible. Replace if necessary.	35
6 Wheelchair Operation	36
6.1 Unfolding and Folding Wheelchair	36
m	36
Warning	36
ALWAYS keep hands and fingers clear of moving parts to avoid injury.	36
DO NOT place hand or fingers on the underside of the seat rail when opening or closing the wheelchair.	36
DO NOT sit or transfer into the wheelchair unless it is fully open and the seat rails are fully seated into the side frame H- blocks.	36
Unfolding the Wheelchair	36
1. Tilt the wheelchair toward you (raising the opposite wheel and caster off the ground/floor).	36
2. Place your hand on the top of the seat rail (A) closest to you where the seat upholstery (B) is attached.	36
3. Point your fingers and thumb to the inside of the wheelchair.	36
4. Press downward on the top of the seat rail until the wheelchair is fully open and the seat rails are fully seated in the H-blocks (C).	36
m	36
Warning	36
Pinch point may occur at the point where the seat rail contacts the H-block.	36
5. Engage both wheel locks, open the footrest/legrest for clearance and transfer into the wheelchair.	36
6. For models equipped with push handles, refer to Securing the Optional Push Handle on page 38.	36
A	37
Folding the Wheelchair	37
1. If equipped with optional push handles, refer to Placing the Optional Push Handle in the Storage Position on page 41.	37
2. Remove the footrests. Refer to Installing/Removing Front Riggings on page 44 or Refer to Installing/Removing Elevating Legrests on page 47.	37
3. With both hands, grasp the middle of the seat upholstery (A) at the front and back edge and lift up.	37
m	37
caution	37
DO NOT allow upholstery to hang between the cross braces.	37
4. Place excess seat upholstery over the armrest.	37
A	37
FIGURE 2 Folding the Wheelchair	37
6.2 Securing the Optional Push Handle	38
MyOn Jr	38
i	38
The wheelchair is shipped with push handle in storage position.	38
1. Unfold the chair. Refer to Unfolding and Folding Wheelchair on page 36.	38
2. Remove the lever (A) by turning counter clockwise.	38
3. Rotate the push handle bar (B) to horizontal position.	38
A	38
4. Rotate the push handle bar (B) to the vertical position.	39
5. Rotate the push handle bar (B) to approx. 45° angle.	39
B	39
6. Partially reinstall the lever (A) into the back cane (C) leaving some threads (D) exposed.	40
7. Rotate push handle (B) down until clamp (E) encompasses threads of lever.	40
8. Secure lever and clamp to push handle by rotating lever clockwise.	40
A	40
MyOn and MyOn Heavy Duty	40
1. Rotate the knob (A) counter clockwise to loosen but do not remove.	40
2. Rotate push handle (B) toward other back cane (C) and engage knob.	40
3. Rotate the knob clockwise to tighten and secure push handle in place.	40
A	41
6.3 Placing the Optional Push Handle in the Storage Position	41
1. Remove the lever (A) from left hand back cane (B).	41
2. Rotate and swivel push handle bar (C) into storage position as shown.	41
3. Reinstall lever into back cane.	41
A	41
FIGURE 7 Placing the Optional Push Handle in the Storage Position	41
6.4 Using Wheel Locks	42
m	42
caution	42
DO NOT attempt to stop a moving wheelchair with the wheel locks. Wheel locks are NOT brakes.	42
If wheel locks DO NOT hold the occupied wheelchair in place, contact a qualified technician - otherwise injury or damage may occur.	42
Push to Lock	42
i	42
Ensure wheelchair is not moving before engaging.	42
1. To engage, (from the seated position) push the wheel lock handle (A) forward until the wheel lock shoe (B) contacts the wheel (C).	42
2. To disengage, (from the seated position) pull the wheel lock handle (A) rearward until the wheel lock shoe (B) disengages the wheel (C).	42
A	42
Pull to Lock	43
i	43
Ensure wheelchair is not moving before engaging.	43
1. To engage, (from the seated position) pull the wheel lock handle (A) rearward until the wheel lock shoe (B) contacts the wheel (C).	43
2. To disengage, (from the seated position) push the wheel lock handle forward until the wheel locks shoe disengages the wheel.	43
A	43
6.5 Folding Wheel Lock Handles	43
1. Pull up and back on the wheel lock handle (A).	43
A	43
6.6 Installing/Removing Front Riggings	44
MyOn and MyOn Heavy Duty	44
i	44
For maintenance and/or adjustment procedures, refer to Troubleshooting and Maintenance on page 64.	44
Installing	44
1. Position the front rigging assembly (A) to the side of the wheelchair frame (B).	44
2. Insert footrest mounting pin (C) into mounting tube (D).	44
3. Rotate the front rigging assembly towards the inside of the wheelchair until it locks into place.	44
i	44
The footplate will be on the inside of the wheelchair when locked in place.	44
4. Repeat this procedure for the other front rigging assembly.	44
C	44
Removing	45
1. Pull the front rigging release lever (A).	45
2. If desired, rotate front rigging assembly (B) outward or inward.	45
3. Lift the front rigging assembly off of the mounting tube (C).	45
C	45
MyOn JR	45
Installing	45
i	45

Match case Limit results 1 per page

TROUBLESHOOTING AND MAINTENANCE

Invacare® MyOn

™

MyOn Jr Wheelchairs

Part No 1167418

The wheels, casters, and tires should be checked periodically for cracks and wear, and should be replaced when necessary. Contact a qualified

technician or Invacare customer support at the telephone numbers on the back of this manual.

Periodically adjust wheel locks in correlation to tire wear. Refer to Adjusting Anti-Tippers

on page 104.

Regularly check for loose spokes in the rear wheels. If loose, have them adjusted. Contact a qualified technician or Invacare customer support

at the telephone numbers on the back of this manual.

Periodically check handrims to ensure they are secured to the rear wheels. Refer to Replacing Handrims

on page 96.

Periodically check caster wheel bearings to make sure they are clean and free from moisture. Use a Teflon

lubricant if necessary.

10.

Hand grips should be checked monthly for wear/looseness/deterioration. Clean if desired. Replace if looseness or deterioration is found.

11.

On a monthly basis, for the 80° and 90° front riggings, check the mounting pin for excessive wear or damage. Replace mounting pin if worn or damaged.

12.

Inspect front rigging mounting pin and hardware. Specifically, inspect the mounting screw that secures the mounting pin to the front rigging.

Tighten if mounting screw is loose.

CAUTION

As with any vehicle, the wheels and tires should be checked periodically for cracks and wear, and should be replaced if

damaged.



Tire wear is excessive if:

•

Pneumatic Tires - there is missing tread or the tires are bald.

•

Urethane Tires - there are cuts, surface defects or the tires are loose on the rims.

•

Rubber Tires - 30% or more of the tire has worn away.

Invacare recommends that rear wheel tire/tube and caster tire/tube be replaced every five years.

WARNING

When cleaning rear cane or hand grip areas use only a clean towel lightly dampened with cool water. Verify that grips are

dry prior to use. Use of soap or ammonia based cleaning solutions will result in the hand grips sliding off the cane assembly.

Failure to observe this warning may result in injury to the user or bystanders.