Home » HP Manuals » Racks & Stands » HP R1.5 » Manual Viewer

HP R1.5 UPS R12000 XR Models User Guide - Page 30

Alarms, Table 3-2

Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

LCD Configuration and Status Alarms If an alarm exists, one or more of the following alarms will display on the LCD panel. For a descriptive list of alarm causes, refer to the section, "LCD Alarm Troubleshooting," in Chapter 5. Table 3-2: Alarms Ambient Over Temperature Automatic Shutdown Pending Batteries Disconnected Battery DC Over Voltage Battery Low Battery n Needs Service Battery Not Charged Battery n Test Failed Bypass Not Available Calibration Failed DC Link Over Voltage Fan Failure Fuse Failure Heatsink Over Temperature Input AC Over Voltage Input AC Under Voltage Input Under Or Over Frequency Internal Communications Failure Inverter Contactor Open Inverter Fault Inverter Output Over Current Inverter Startup Failure Inverter Uncalibrated Level 2 Overload - Phase A Level 3 Overload - Phase A Level 4 Overload - Phase A Loss of Redundancy Loss of Sync-Bus Low Battery Shutdown Non-volatile Memory Checksum Fail On Manual Bypass Output AC Over Voltage Output AC Under Voltage Output Overload Program Checksum Fail Rectifier Input Over Current Remote Emergency Power Off Software Incompatibility Detected UPS On Battery UPS On Bypass Utility Fail Utility Not Present 3-6 HP Uninterruptible Power System R12000 XR Models User Guide

Section	Page
HP Uninterruptible Power System R12000 XR Models User Guide	1
Notice	2
Contents	3
About This Guide	6
Intended Audience	6
Important Safety Information	6
Symbols on Equipment	6
Rack Stability	7
Symbols in Text	7
Text Conventions	7
Related Documents	8
Getting Help	8
HP Technical Support	8
HP Website	8
HP Authorized Reseller	9
Reader’s Comments	9
Chapter 1: Overview	10
UPS Features	10
Communication Ports	11
UPS R12000 XR Model Part Number	11
Front View	12
Rear View	13
Power Management Software	14
UPS Hardware Options	14
Extended Runtime Modules	15
Power Distribution Units	15
Remote Emergency Power Off Port	15
Warranties	16
$25,000 Computer Load Protection Guarantee	16
Pre-Failure Battery Warranty	16
Chapter 2: Operation	17
Front Panel Controls and LCD Display	17
Front Panel Indicators	18
Front Panel LCD	18
Front Panel LEDs	19
Modes of Operation	20
Turning on the Main Circuit Breaker	21
Charging the Batteries	21
Placing the UPS in Operate Mode	22
Initiating a Self-Test	22
Audible Alarms	23
Silencing an Audible Alarm	23
Placing the UPS in Bypass Mode	24
Shutting Down the System	24
Chapter 3: LCD Configuration and Status	25
Changing Configuration Parameters	25
Matching the Utility Voltage	26
Module Locations	27
Configuring the UPS Using the LCD Menu	28
Initial Power-Up Display	28
Top Level Main Menu	28
Menu Map	29
Alarms	30
Displaying the Status or Active Alarms	31
Main Module (MM) Status and Alarms	31
Electronics Modules (M1-M4) Status and Alarms	32
Displaying the Frequency, Power, and Current Data	33
Displaying the Battery Charge Data	34
Setting the Time	34
Setting the Date	34
Displaying the Firmware Version	35
Testing the LCD Display	35
Changing the System Setup Options	36
Setting the Baud Rate	36
Setting the Voltage	37
Setting the Hardware Configuration	37
Setting the Language	38
Setting the Password	38
Chapter 4: Battery Maintenance	39
Precautions	39
Charging Batteries	40
Determining When to Replace Batteries	40
Obtaining New Batteries	41
Replacing the Batteries	41
Removing and Replacing the Battery Module	42
Testing the New Battery Module	43
Conducting a Battery Commissioning Test	43
Disposing of Used Batteries	43
Care and Storage of Batteries	44
Pre-Failure Battery Warranty	44
Chapter 5: Troubleshooting	45
LCD Alarm Troubleshooting	45
Problems During Startup	54
Problems After Startup	54
CarePaq Considerations	56
Repairing the UPS	56
Appendix A: Regulatory Compliance Notices	57
Regulatory Compliance Serial Numbers	57
Federal Communications Commission Notice	57
Class A Equipment	57
Class B Equipment	58
Declaration of Conformity for Products Marked with the FCC Logo, United States Only	58
Modifications	58
Cables	59
Canadian Notice (Avis Canadien)	59
Class A Equipment	59
Class B Equipment	59
European Union Notice	59
Japanese Notice	60
BSMI Notice	60
Battery Replacement Notice	61
Appendix B: Electrostatic Discharge	62
Preventing Electrostatic Damage	62
Grounding Methods To Prevent Electrostatic Damage	62
Appendix C: Specifications	63
Physical Specifications	63
Input Specifications	63
Output Specifications	64
Overcurrent Protection	64
Battery Specifications	65
Battery Runtime	65
Environmental Specifications	65