HP EliteDesk 705 G3 Micro Maintenance and Service Guide - Page 35

covers up and out of the chassis or use a, If you are installing an expansion card in a vacant socket

Get HP EliteDesk 705 G3 Micro PDF manuals and user guides View all HP EliteDesk 705 G3 Micro manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

3. Release the slot cover retention latch that secures the slot covers by lifting the tab on the latch and rotating the latch to the open position. 4. Locate the correct vacant expansion socket on the system board and the corresponding expansion slot on the back of the computer chassis. 5. Before installing an expansion card, remove the expansion slot cover or the existing expansion card. NOTE: Before removing an installed expansion card, disconnect any cables that may be attached to the expansion card. a. If you are installing an expansion card in a vacant socket, you must slide one of the expansion slot covers up and out of the chassis or use a flat-bladed screwdriver to pry out one of the metal shields on the rear panel that covers the expansion slot. Be sure to remove the appropriate shield for the expansion card you are installing. Expansion cards 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
3.
Release the slot cover retention latch that secures the slot covers by lifting the tab on the latch and
rotating the latch to the open position.
4.
Locate the correct vacant expansion socket on the system board and the corresponding expansion slot
on the back of the computer chassis.
5.
Before installing an expansion card, remove the expansion slot cover or the existing expansion card.
NOTE:
Before removing an installed expansion card, disconnect any cables that may be attached to
the expansion card.
a.
If you are installing an expansion card in a vacant socket, you must slide one of the expansion slot
covers up and out of the chassis or use a
flat-bladed
screwdriver to pry out one of the metal
shields on the rear panel that covers the expansion slot. Be sure to remove the appropriate shield
for the expansion card you are installing.
Expansion cards
27