HP Elite Dragonfly G2 Maintenance and Service Guide - Page 57

Display assembly, Peel the antennas

Get HP Elite Dragonfly G2 PDF manuals and user guides View all HP Elite Dragonfly G2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

Before removing the WWAN antennas and cables, follow these steps: 1. Prepare the computer for disassembly (Preparation for disassembly on page 30). 2. Remove the bottom cover (Bottom cover on page 30). 3. Remove the battery (see Battery on page 31). 4. Remove the heat sink and fan assembly (see Heat sink and fan assembly on page 38). 5. Remove the system board (see System board on page 46). 6. Remove the speaker assembly (see Speakers on page 43). Remove the WWAN antennas and cables: 1. Disconnect the antenna cables from the WWAN module (1), and then remove the cables from the clips on the USB board (2). 2. Disconnect the cable from the ZIF connector on the WWAN antenna (3). 3. Peel the antennas off the computer (4) to remove them. Reverse this procedure to install the WWAN antennas and cables. Display assembly To remove and disassemble the display assembly, use these procedures and illustrations. Component replacement procedures 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
Before removing the WWAN antennas and cables, follow these steps:
1.
Prepare the computer for disassembly (
Preparation for disassembly
on page
30
).
2.
Remove the bottom cover (
Bottom cover
on page
30
).
3.
Remove the battery (see
Battery
on page
31
).
4.
Remove the heat sink and fan assembly (see
Heat sink and fan assembly
on page
38
).
5.
Remove the system board (see
System board
on page
46
).
6.
Remove the speaker assembly (see
Speakers
on page
43
).
Remove the WWAN antennas and cables:
1.
Disconnect the antenna cables from the WWAN module
(1)
, and then remove the cables from the clips
on the USB board
(2)
.
2.
Disconnect the cable from the ZIF connector on the WWAN antenna
(3)
.
3.
Peel the antennas
off
the computer
(4)
to remove them.
Reverse this procedure to install the WWAN antennas and cables.
Display assembly
To remove and disassemble the display assembly, use these procedures and illustrations.
Component replacement procedures
49