HP C7745NB HP SureStore Tape Autoloader Model 1/9 User and Service Guide - Page 31

Verifying the Host Configuration

Get HP C7745NB - SureStore DLT Tape Autoloader 1/9 PDF manuals and user guides View all HP C7745NB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Chapter 1 Verifying the Host Configuration Remember to: Check that the autoloader is properly connected to the host (see Figure 9 on page 30). Power on the autoloader and then the host (see Figure 9 on page 30). Verify that your backup software package is compatible with your autoloader. Most backup software packages require an additional module to communicate with the autoloader robotics. You can view the software compatibility matrix at http://www.hp.com/go/storage. Install the HP Library & Tape Tools diagnostic/installation check utility available at http://www.hp.com/support/TapeTools onto your host system (if your operating system supports this tool). This utility verifies that the autoloader is connected and communicating with the host. It also verifies that the autoloader is functioning and provides diagnostic information. See Running Autoloader Diagnostics Tests on page 85 for more information on HP Library & Tape Tools. Windows NT and 2000 For Window™ operating systems, perform the following operating system configurations: Install the appropriate host bus adapter(s) Install the corresponding drivers for the interface card(s) Install the backup software To verify the installation, look for the library and drive after powering up the host. Go into Settings -> Control Panel -> SCSI Adapter Run a test backup to ensure that all components are properly configured. Note Consult your software documentation for more information on installing, configuring, and operating your backup software. Chapter 1 Verifying the Host Configuration 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
Chapter 1
Verifying the Host Configuration
31
Chapter 1
Verifying the Host Configuration
Remember to:
Check that the autoloader is properly connected to the host (see
Figure 9
on page 30
).
Power on the autoloader and then the host (see
Figure 9
on page 30
).
Verify that your backup software package is compatible with your
autoloader. Most backup software packages require an additional module
to communicate with the autoloader robotics. You can view the software
compatibility matrix at
.
Install the HP Library & Tape Tools diagnostic/installation check utility
available at
onto your host
system (if your operating system supports this tool). This utility verifies that
the autoloader is connected and communicating with the host. It also
verifies that the autoloader is functioning and provides diagnostic
information. See
Running Autoloader Diagnostics Tests
on page 85
for
more information on HP Library & Tape Tools.
Windows NT and 2000
For Window™ operating systems, perform the following operating system
configurations:
Install the appropriate host bus adapter(s)
Install the corresponding drivers for the interface card(s)
Install the backup software
To verify the installation, look for the library and drive after powering up the
host.
Go into
Settings
->
Control Panel
->
SCSI Adapter
Run a test backup to ensure that all components are properly configured.
Note
Consult your software documentation for more information on
installing, configuring, and operating your backup software.