Harman Kardon AVR 2600 Owners Manual - Page 11

AM and FM Antenna Terminals, Front, Center and Surround Speaker Outputs, Surround Back/Zone 2 - remote

Get Harman Kardon AVR 2600 PDF manuals and user guides View all Harman Kardon AVR 2600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

REAR - PANEL CONNECTIONS NOTES: • Due to copy-protection restrictions, there is no output at the Component Video Monitor Outputs for HDCP-copyprotected sources. • Composite video signals are upscaled to as high as 1080i and available at these outputs. If your video display's best connection is component video, it is the only video connection required from the AVR to the display. AM and FM Antenna Terminals: Connect the included AM and FM antennas to their respective terminals for radio reception. Front, Center and Surround Speaker Outputs: Use two-conductor speaker wire to connect each set of terminals to the correct speaker. Remember to observe the correct polarity (positive and negative connections). Surround Back/Zone 2 Speaker Outputs: These speaker outputs are used for the surround back channels in a 7.1channel home theater, or may be reassigned to a remote room for multizone operation. Switched AC Accessory Outlet: You may plug the AC power cord of one source device into this outlet, and it will turn on whenever you turn on the receiver. Do not use a source that consumes more than 50 watts of power. AC Power Cord: After you have made all other connections, plug the AC power cord into an unswitched wall outlet. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
11
REAR- PANEL CONNECTIONS
NOTES:
• Due to copy-protection restrictions, there is no output at
the Component Video Monitor Outputs for HDCP-copy-
protected sources.
• Composite video signals are upscaled to as high as 1080i
and available at these outputs. If your video display’s best
connection is component video, it is the only video connec-
tion required from the AVR to the display.
AM and FM Antenna Terminals:
Connect the included
AM and FM antennas to their respective terminals for radio reception.
Front, Center and Surround Speaker Outputs:
Use two-conductor speaker wire to connect each set of terminals
to the correct speaker. Remember to observe the correct polarity
(positive and negative connections).
Surround Back/Zone 2 Speaker Outputs:
These
speaker outputs are used for the surround back channels in a 7.1-
channel home theater, or may be reassigned to a remote room for
multizone operation.
Switched AC Accessory Outlet:
You may plug the
AC power cord of one source device into this outlet, and it will turn
on whenever you turn on the receiver. Do not use a source that
consumes more than 50 watts of power.
AC Power Cord:
After you have made all other connections,
plug the AC power cord into an unswitched wall outlet.