Harbor Freight Tools 44914 User Manual

Harbor Freight Tools 44914 - 1/4 in. Trim Router Manual

Get Harbor Freight Tools 44914 - 1/4 in. Trim Router PDF manuals and user guides View all Harbor Freight Tools 44914 manuals
Add to My Manuals
Save this manual to your list of manuals

Harbor Freight Tools 44914 manual content summary:

  • Harbor Freight Tools 44914 | User Manual - Page 1
  • Harbor Freight Tools 44914 | User Manual - Page 2
    General power Tool Safety Warnings Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save lose control. Page 2 For technical questions, please call 1-800-444-3353. Item 44914 MAINTENANcE
  • Harbor Freight Tools 44914 | User Manual - Page 3
    power tool accidentally. 4. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. OpERATION MAINTENANcE Item
  • Harbor Freight Tools 44914 | User Manual - Page 4
    serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. Router seq.) 15. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that
  • Harbor Freight Tools 44914 | User Manual - Page 5
    doctor and then have regular medical check-ups to ensure medical problems are not being caused or worsened from use. Pregnant women or explained in this manual. If any abnormal vibration occurs, stop use immediately. SAVE THESE INSTRUcTIONS. SETUp OpERATION MAINTENANcE Item 44914 For technical
  • Harbor Freight Tools 44914 | User Manual - Page 6
    not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use. If the plug will not fit the outlet, have a proper outlet installed by a qualified OpERATION MAINTENANcE Page 6 For technical questions, please call 1-800-444-3353. Item 44914
  • Harbor Freight Tools 44914 | User Manual - Page 7
    Risk of Eye Injury. Wear ANSI-approved safety goggles with side shields. Read the manual before set-up and/or use. WARNING marking concerning Risk of Fire. Do not cover cord to appropriate outlet. OpERATION MAINTENANcE Item 44914 For technical questions, please call 1-800-444-3353. Page 7
  • Harbor Freight Tools 44914 | User Manual - Page 8
    at the beginning of this manual including all text under subheadings therein before set up or use of this product. Functions Fence Wing Nut Switch Router Fence Bracket Base Knob SETUp OpERATION MAINTENANcE Attachment Knob Page 8 Edge Knob Trim Guide Lock Knob For technical questions
  • Harbor Freight Tools 44914 | User Manual - Page 9
    Instructions Read the ENTIRE IMpORTANT SAFETy INFORMATION section at the beginning of this manual performing any procedure in this section. Installing the Router Bit 1. Unplug the Router from the electrical outlet. 2. Place the Small 44914 For technical questions, please call 1-800-444-3353. Page
  • Harbor Freight Tools 44914 | User Manual - Page 10
    Router, as shown in Figure A. 3. After measuring the proper distance from the router measuring the proper distance from the router bit to the temporary guide, tighten the Fence using the Use with a Temporary Guide and for circle Fence to the far edge of the router bit equal to the radius of the
  • Harbor Freight Tools 44914 | User Manual - Page 11
    Router must be adjusted to cut accurately in two dimensions. 1. Assemble the Trim Guide as shown in Figure c, and attach to the Router Base. 2. Adjust the Router , nearby that will present a hazard while working. General Operating Instructions 1. Make sure that the Power Switch is in the off-
  • Harbor Freight Tools 44914 | User Manual - Page 12
    Servicing procedures not specifically explained in this manual noise or vibration occurs, have the problem corrected before further use. cleaning, Periodically wipe the Collet, Collet Cone, and router bits with a light oil to prevent rust. by a qualified service technician. SETUp OpERATION MAINTENANcE Page
  • Harbor Freight Tools 44914 | User Manual - Page 13
    SAFETy Troubleshooting problem Tool will not Carbon brushes worn decreases over time. or damaged. 2. Router bit dull or damaged. Excessive noise or rattling. Internal diagnosing or servicing the tool. Disconnect power supply before service. SETUp OpERATION MAINTENANcE Item 44914 For
  • Harbor Freight Tools 44914 | User Manual - Page 14
    HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR 101 102 Description Trim Guide Asm. (420~430) Link Countersunk Head Screw Outer Tooth Washer (not shown) Set Plate Edge Knob Screw Guide Wheel Guide Block Flat Washer 44914
  • Harbor Freight Tools 44914 | User Manual - Page 15
    441 440 17 33 16 50 49 48 37 18 46 102 101 28 15 6 1 23 45 10 13 19 51 21 27 29 Item 44914 For technical questions, please call 1-800-444-3353. Page 15 MAINTENANcE
  • Harbor Freight Tools 44914 | User Manual - Page 16
    Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16