Fender Prosonic Owners Manual - Page 5

Rear Panel Functions 12 34 5 6 78 9 10 11 1. LINE CORD - Connect the power line cord to a grounded AC receptacle in accordance with the voltage and frequency ratings as listed on the rear panel of the Prosonic amplifier. 2. POWER SWITCH - Turns the AC power on and off. 3. FUSE - Located in the AC supply of the amplifier, the fuse helps protect the unit from electrical fault or tube failure. Replace a failed fuse with the same type and rating. If the amplifier repeatedly blows fuses, take it to an authorized Fender service center. 4. STANDBY SWITCH - Switches the unit between operate and stand-by modes when the power switch is ON. In stand-by mode, no sound will be heard from the amplifier but power is still supplied to the tube filaments keeping them warm and the unit ready to play. Use this switch during short breaks to increase tube life. Wait at least 50 seconds after the power switch is on before putting the unit into the standby mode. 5. RECTIFIER/BIAS SWITCH - Allows for the selection of rectifier sounds and bias classes to best suit your playing style (experiment to find a preferred setting). The (1) TUBE A setting at low volume sounds much like the (2) TUBE AB2 and (3) S.S. "solid state" AB2 settings at high volume. 6. IMPEDANCE SWITCH (Head only) - Sets the output impedance of the amplifier to match the speaker impedance for maximum power and tube life. 7. SPEAKER (Combo), SPEAKER 1 (Head) - Primary output jack for connection to speakers. A speaker must always be connected at this jack for the unit to be heard. 8. EXTERNAL SPEAKER (Combo), SPEAKER 2 (Head) Output jack for connection to an external speaker. ONLY use in conjunction with the main speaker jack. Using this jack on the Combo automatically switches the amplifier impedance to 8Ω. 9. FOOTSWITCH - Jack for connection to the included footswitch. The footswitch allows remote switching between channels as well as ON/OFF switching of the REVERB effect on the combo unit only. 10.EFFECTS RETURN - Connect cord from external effects devices at this input jack. Inserting a plug at this jack automatically disconnects the unit's internal connection from the pre-amp to the power amp. 11.EFFECTS SEND - Connect cord to external effects devices at this output jack. This jack can also be used as a line out. Specifications PART NUMBER* - COMBO: 021-1077-x00 (100V) 021-1067-x00 (230V) 021-1007-x00 (120V) 021-1037-x00 (240V) Aust 021-1047-x00 (230V) UK 021-1087-x00 (230V) Nordic SPEAKER ENCLOSURE: 2-10" Custom Design Celestion® speakers PART NUMBER* - HEAD: 021-2077-x00 (100V) 021-2067-x00 (230V) 021-2007-x00 (120V) 021-2047-x00 (230V) UK 021-2037-x00 (240V) AUSTRALIA/ NZ POWER REQUIREMENTS: 360W. COMPANION SPEAKER ENCLOSURE: 4 12" Celestion® Vintage 30 speakers: 021-3001-100 (RED) 021-3001-200 (GREEN) 021-3001-000 (BLACK) POWER OUTPUT: Class AB2, Solid state rectifier: 60 W R.M.S. (minimum into 8 or 16 Ω) Class AB2, 5AR4/GZ34 rectifier: 50 W R.M.S. (minimum into 8 or 16 Ω) Class A, 5AR4/GZ34 rectifier: 30 W R.M.S. (minimum into 8 or 16 Ω) OUTPUTIMPEDANCE: 8Ω or 16Ω (Combo), 4Ω, 8Ω or 16Ω, (Head). INPUTIMPEDANCE: 1 MΩ TUBES: COMBO Two (2) Five (5) One (1) One (1) HEAD Two (2) Four (4) None (0) One (1) 5881/6L6WGC 12AX7A 12AT7 5AR4/GZ34 (P/N 099-5090) (P/N 099-5091) (P/N 099-5092) (P/N 099-5097) FUSE TYPE: 100/120V units: T3 Amp/250V, 230-240V version T1.6 Amp 250V DIMENSIONS: HEIGHT: WIDTH: DEPTH: 18.5 in 24 in 10.5 in COMBO (47 cm) (61 cm) (26.5 cm) 9 in. 24 in. 9.5 in. HEAD (23 cm) (61 cm) (24 cm) WEIGHT: 48 lbs. (22 kg) 42 lbs. (19 kg) *For Prosonic COLOR DESIGNATED part number, replace "x" with: 1 = RED, 2 = GREEN, 0 = BLACK (Combo Only) Product specifications are subject to change without notice.