Epson TM-T88V Technical Reference Guide - Page 114

Caution, Nc: No

Get Epson TM-T88V PDF manuals and user guides View all Epson TM-T88V manuals
Add to My Manuals
Save this manual to your list of manuals

Page 114 highlights

Pin Source Compatibility Mode Nibble Mode Byte Mode 28 29 30 31 Host 32 Printer 33 34 Printer 35 Printer 36 Host GND GND GND Init Fault GND DK_STATUS +5V SelectIn GND GND GND Init DataAvail/Data0,4 ND ND ND 1284-Active GND GND GND Init DataAvail ND ND ND 1284-Active NC: Not Connected ND: Not Defined CAUTION  A signal name with a rule above it indicates an "L" active signal.  Bidirectional communications cannot take place, unless all signal names for both sides correspond to each other.  Connect all signal lines using a twisted-pair cable. Connect the return side to the signal ground level.  Make sure the signals satisfy electrical characteristics.  Set the leading edge and trailing edge times to 0.5ms or less.  Do not ignore Ack or BUSY signals during a data transfer. Ignoring such signals may result in data corruption.  Make the interface cables as short as possible. 114

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
114
NC: No
t
Co
nn
ec
t
ed
ND: No
t
Def
in
ed
28
GND
GND
GND
29
GND
GND
GND
30
GND
GND
GND
31
Host
Init
Init
Init
32
Printer
Fault
DataAvail/Data0,4
DataAvail
33
GND
ND
ND
34
Printer
DK_STATUS
ND
ND
35
Printer
+5V
ND
ND
36
Host
SelectIn
1284-Active
1284-Active
CAUTION
A signal name with a rule above it indicates an “L” active signal.
Bidirectional communications cannot take place, unless all signal names for both sides
correspond to each other.
Connect all signal lines using a twisted-pair cable. Connect the return side to the signal
ground level.
Make sure the signals satisfy electrical characteristics.
Set the leading edge and trailing edge times to 0.5ms or less.
Do not ignore Ack
or BUSY signals during a data transfer. Ignoring such signals may
result in data corruption.
Make the interface cables as short as possible.
Pin
Source
Compatibility
Mode
Nibble Mode
Byte Mode