Dell OptiPlex Micro 7020 Owners Manual - Page 79

Removing SMA antenna assembly, Installing the antenna module black cable

Get Dell OptiPlex Micro 7020 PDF manuals and user guides View all Dell OptiPlex Micro 7020 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 79 highlights

Figure 53. Installing the antenna module (black cable) Steps 1. Place the antenna module (black cable) on the chassis. 2. Align the captive screw on the antenna module (black cable) to the screw hole on the chassis. 3. Tighten the captive screw that secures the antenna module (black cable) to the chassis. 4. Route the antenna cable through the routing guides on the chassis. Next steps 1. Install the system board NOTE: The system board can be installed with the memory, coin-cell battery, and processor preattached. 2. Install the optional I/O module (HDMI/VGA/DP/Serial/PS2) or the optional Type-C module, whichever is applicable. 3. Install the fan. 4. Install the wireless card. 5. Install the heat sink. 6. Install the M.2 2230 solid-state drive or M.2 2280 solid-state drive, whichever is applicable. 7. Install the speaker. 8. Install the side cover. 9. Follow the procedure in After working inside your computer. Removing SMA antenna assembly CAUTION: The information in this section is intended for authorized service technicians only. Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the side cover. 3. Remove the wireless card. Removing and installing Field Replaceable Units (FRUs) 79

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
Figure 53. Installing the antenna module (black cable)
Steps
1.
Place the antenna module (black cable) on the chassis.
2.
Align the captive screw on the antenna module (black cable) to the screw hole on the chassis.
3.
Tighten the captive screw that secures the antenna module (black cable) to the chassis.
4.
Route the antenna cable through the routing guides on the chassis.
Next steps
1.
Install the
system board
NOTE:
The system board can be installed with the memory, coin-cell battery, and processor preattached.
2.
Install the
optional I/O module (HDMI/VGA/DP/Serial/PS2)
or the
optional Type-C module
, whichever is applicable.
3.
Install the
fan
.
4.
Install the
wireless card
.
5.
Install the
heat sink
.
6.
Install the
M.2 2230 solid-state drive
or
M.2 2280 solid-state drive
, whichever is applicable.
7.
Install the
speaker
.
8.
Install the
side cover
.
9.
Follow the procedure in
After working inside your computer
.
Removing SMA antenna assembly
CAUTION:
The information in this section is intended for authorized service technicians only.
Prerequisites
1.
Follow the procedure in
before working inside your computer
.
2.
Remove the
side cover
.
3.
Remove the
wireless card
.
Removing and installing Field Replaceable Units (FRUs)
79