D-Link DIR-878 User Manual - Page 43

PPPoE Session, Username, Password, Address Mode, IP Address, Service Name, Reconnect, DNS Type,

Page 43 highlights

Section 3 - Configuration PPPoE Select PPPoE (Point-to-Point-Tunneling Protocol) if your Internet connection requires you to enter a username and password. This information can be provided by your Internet service provider (ISP). Required fields will vary, depending on the options you have enabled. PPPoE Session: Choose Share with IPv4 to re-use your IPv4 PPPoE username and password, or Create a new session. Username: If you selected Create a new session above, enter the PPPoE Username provided by your ISP. Password: If you selected Create a new session above, enter the PPPoE Password provided by your ISP. Address Mode: Select Static IP if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic IP. IP Address: Enter the IP Address provided by your ISP (for Static IP only). Service Name: If you selected Create a new session above, enter the ISP Service Name (optional). Reconnect If you selected Create a new session above, select either Always Mode: on, On demand, or Manual. MTU: Maximum Transmission Unit - you may need to change the MTU for optimal performance with your ISP. DNS Type: Select either Obtain DNS server address or Use the following DNS . Primary DNS If you selected Use the following DNS, enter the Primary DNS Server: Server address. Secondary DNS If you selected Use the following DNS, enter the Secondary DNS Server: Server address. D-Link DIR-878 User Manual 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124

39
D-Link DIR-878 User Manual
Section 3 - Configuration
PPPoE
Choose
Share with IPv4
to re-use your IPv4 PPPoE username and
password, or
Create a new session
.
If you selected
Create a new session
above, enter the PPPoE
Username
provided by your ISP.
If you selected
Create a new session
above, enter the PPPoE
Password
provided by your ISP.
Select
Static IP
if your ISP assigned you the IP address, subnet mask,
gateway, and DNS server addresses. In most cases, select
Dynamic IP
.
Enter the
IP Address
provided by your ISP (for Static IP only).
If you selected
Create a new session
above, enter the ISP
Service
Name
(optional).
If you selected
Create a new session
above, select either
Always
on
,
On demand
, or
Manual
.
Maximum Transmission Unit - you may need to change the MTU for
optimal performance with your ISP.
Select either
Obtain DNS server address
or
Use the following DNS
.
If you selected
Use the following DNS
, enter the
Primary DNS
Server
address.
If you selected
Use the following DNS
, enter the
Secondary DNS
Server
address.
PPPoE Session:
Username:
Password:
Address Mode:
IP Address:
Service Name:
Reconnect
Mode:
MTU:
DNS Type:
Primary DNS
Server:
Secondary DNS
Server:
Select
PPPoE
(Point-to-Point-Tunneling Protocol) if your Internet connection requires you to enter a username and password. This information can be
provided by your Internet service provider (ISP). Required fields will vary, depending on the options you have enabled.