D-Link DES-3624i User Guide - Page 63

Con MAC Address Filtering, Con Static Multicast Filtering

Get D-Link DES-3624i PDF manuals and user guides View all D-Link DES-3624i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

Stackable NWay Ethernet Switch User's Guide for the same MAC address. Static filters always take precedence over static forwarding entries. The Switch will automatically upgrade the Status to "in use" once the static filter is removed. Configure MAC Address Filtering The Static Filtering Table screen contains filtering information configured into the Switch by (local or network) management specifying destination addresses which are not allowed to be forwarded. The Switch will check both the destination and source MAC addresses on all packets. To access the Static Filtering Table screen, select Configure Filtering and Forwarding Table from the System Configuration menu. Then select Configure MAC Address Filtering from the bottom of the Configure Filtering and Forwarding Table screen. The following screen appears: Figure 6-22. Static Filtering Table screen To make a change to this screen, choose Add or Remove in the Action field. Then enter the MAC Address and VID. Press APPLY to let the changes take effect. Configure Static Multicast Filtering Multicast filtering allows you to block or forward traffic over each port for one multicast group. To access the Static Multicast Filtering Table Configuration screen, select Configure Filtering and Forwarding Table from the System Configuration menu. Then select Configure Static Multicast Filtering from the bottom of the Configure Filtering and Forwarding Table screen. The following screen appears: Using the Console Interface 63

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
Stackable NWay Ethernet Switch User’s Guide
Using the Console Interface
63
for the same MAC address. Static filters always take precedence over static forwarding entries. The Switch will
automatically upgrade the Status to “in use” once the static filter is removed.
Configure MAC Address Filtering
The
Static Filtering Table
screen
contains filtering information configured into the Switch by (local or network)
management specifying destination addresses which are not allowed to be forwarded. The Switch will check both the
destination and source MAC addresses on all packets.
To access the
Static Filtering Table
screen, select
Configure Filtering and Forwarding Table
from the
System Configuration
menu. Then select
Configure MAC Address Filtering
from the bottom of the
Configure
Filtering and Forwarding Table
screen. The following screen appears:
Figure 6-22.
Static Filtering Table screen
To make a change to this screen, choose
Add
or
Remove
in the Action field. Then enter the MAC Address
and VID. Press
APPLY to let the changes take effect.
Configure Static Multicast Filtering
Multicast filtering
allows you to block or forward traffic over each port for one multicast group.
To access the
Static Multicast Filtering Table Configuration
screen, select
Configure Filtering and
Forwarding Table
from the
System Configuration
menu. Then select
Configure Static Multicast Filtering
from the bottom of the
Configure Filtering and Forwarding Table
screen. The following screen appears: