Cub Cadet CC 30 H Operation Manual - Page 9
Install the Rear Engine Cover If equipped - rider
View all Cub Cadet CC 30 H manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 9 highlights
2. Install the deck chute (b) into the deck discharge opening on the deck. The rear of the chute (b) should be under the tab (f) on the rear deck bracket (g). The studs (c) on the deck surface will fit through the holes on the upper portion of the deck chute (b). The small tab (d) on the deck lip area will fit through the square cutout on the lower portion of the deck chute (b). See Figure 2-9. Note: Make certain that the upper-rear portion of deck chute (b) is depressing the safety switch (e) located on the deck surface and under the tab (f) on the rear deck bracket (g). The engine will not start without the deck chute (b) properly in place. 3. Secure the deck chute (b) by tightening the wing knobs (a) removed in step 1. See Figure 2-9. Installing the Mulch Plug (If equipped) WARNING Never operate this riding mower without either the mulch plug or deck chute installed. 1. Remove the wing knobs (a) installed on the mowing deck and retain for later installation. See Figure 2-10. (a) (a) (b) (c) (f) (e) (g) (c) (d) Figure 2-10 2. Install the mulch plug (b) into the deck discharge opening on the deck. The rear of the mulch plug (b) should be under the tab (f) on the rear deck bracket (g). The studs (c) on the deck surface will fit through the holes on the upper portion of the mulch plug (b). The small tab (d) on the deck lip area will fit through the square cutout on the lower portion of the mulch plug (b). See Figure 2-10. Note: Make certain that the upper-rear portion of mulch plug (b) is depressing the safety switch (e) located on the deck surface and under the tab (f) on the rear deck bracket (g). The engine will not start without the mulch plug (b) properly in place. 3. Secure the mulch plug (b) by tightening the wing knobs (a) removed in step 1. Install the Rear Engine Cover (If equipped) 1. Remove the two factory installed hex screws (a) located on the rear engine cover (b). Retain the hex screws (a) for later instructions. See Figure 2-11. (b) (a) (a) Figure 2-11 2. Install the rear engine cover (b) by positioning it in place as shown in Figure 2-11 Tip the rear engine cover (b) forward to fit it into the slots provided, then rotate it backwards to align the mounting holes. 3. Secure the rear engine cover (b) with the two hex screws (a) removed in Step 1. Do not over-tighten. Installing the Hitch Plate 1. Slide the hitch plate (a) in between the frame (b) and the rear cover (c) on your rider. See Figure 2-12. (c) (b) (a) (d) (d) Figure 2-12 2. When the holes in the hitch plate (a) and the frame (b) are aligned, install the two hex screws (d) up through the frame (b) and into the hitch plate (a). See Figure 2-12. 3. Securely tighten the hex screws (d). Installing the Bumper (If equipped) 1. Remove the two screws (a) as shown in Figure 2-13. (b) (a) (a) Figure 2-13 2. Position the bumper (b) over the mounting holes and secure using the screws (a) removed in Step 1. See Figure 2-13. Connecting the Battery Cables WARNING California Proposition 65 Warning: Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling CAUTION When attaching battery cables, always connect the POSITIVE (Red) wire to its terminal first, followed by the NEGATIVE (Black) wire. For shipping reasons, both battery cables on your equipment may have been left disconnected from the terminals at the factory. To connect the battery cables, proceed as follows: Note: The positive battery terminal is marked POS. (+). The negative battery terminal is marked NEG. (-). 1. Remove the factory installed hex bolts (a) and sems nuts (b) located on the end of the wiring harness. Retain the hardware for later instructions. See Figure 2-14. (c) (c) (e) (d) (a) (g) (a) (b) (b) (f) Figure 2-14 Section 2 - Assembly & Set-Up 9