Canon REALiS LCOS 4K501ST MULTIMEDIA PROJECTOR 4K501ST Users Manual - Page 124

Serial communication, Power management mode, Power management duration

Get Canon REALiS LCOS 4K501ST PDF manuals and user guides View all Canon REALiS LCOS 4K501ST manuals
Add to My Manuals
Save this manual to your list of manuals

Page 124 highlights

Menu Settings Serial communication > [System settings] > [Serial communication] You can check setting values for the service port (CONTROL) used for serial communication. Option Baud rate Data bits Parity Function Modulation rate, in bits per second. Number of bits of data. Number of parity bits. Specify the length of the mark representing the end of data bits. Stop bit Option 1 2 Function Sets the stop bit length to 1. Sets the stop bit length to 2. Power management mode > [System settings] > [Power management mode] You can specify to turn off the lamp or projector automatically after a certain period if the projector and remote control are not used and there is no input signal. Option Disabled Lamp off Standby Function Disable power management mode. Only turns the lamp off. Turns the projector off and puts it in standby. • After the lamp is turned off, projection resumes when: - the same input signal is restored. - the remote control or projector is operated. - the power is turned on. • After the projector enters standby, restoring projection requires the same steps as when turning the projector on normally. • When [Disabled] is selected, [Direct power on] (P125) is not available. Power management duration > [System settings] > [Power management duration] Specify how long before the lamp is turned off or the projector enters standby, depending on the [Power management mode] setting. Option 5 min. - 60 min. Function After 30 seconds without an input signal when the projector is idle, the projector starts displaying a countdown of the selected time. • If conditions that would start countdown are met while you are blanking projection, blanking is canceled. • Once countdown begins, audio output stops. 124

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
Menu Settings
124
Serial communication
> [System settings] >
[Serial communication]
You can check setting values for the service port (CONTROL) used for serial
communication.
Power management mode
> [System settings] >
[Power management mode]
You can specify to turn off the lamp or projector automatically after a certain period
if the projector and remote control are not used and there is no input signal.
Power management duration
> [System settings] >
[Power management duration]
Specify how long before the lamp is turned off or the projector enters standby,
depending on the [Power management mode] setting.
Option
Function
Baud rate
Modulation rate, in bits per second.
Data bits
Number of bits of data.
Parity
Number of parity bits.
Stop bit
Specify the length of the mark representing the end of data bits.
Option
Function
Disabled
Disable power management mode.
Lamp off
Only turns the lamp off.
Standby
Turns the projector off and puts it in standby.
•
After the lamp is turned off, projection resumes when:
-
the same input signal is restored.
-
the remote control or projector is operated.
-
the power is turned on.
•
After the projector enters standby, restoring projection requires the same steps as when
turning the projector on normally.
•
When [Disabled] is selected, [Direct power on] (
P125
) is not available.
Option
Function
5 min. - 60 min.
After 30 seconds without an input signal when the projector is idle,
the projector starts displaying a countdown of the selected time.
•
If conditions that would start countdown are met while you are blanking projection,
blanking is canceled.
•
Once countdown begins, audio output stops.
Option
Function
1
Sets the stop bit length to 1.
2
Sets the stop bit length to 2.