Adaptec 29320LPE User Guide - Page 59

Windows Error Messages, x097] Unable to allocate memory - means

Get Adaptec 29320LPE - SCSI Card Storage Controller U320 320 MBps PDF manuals and user guides
UPC - 760884154762
View all Adaptec 29320LPE manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Chapter D: Troubleshooting ● 59 [xxxxx081] SCSI card initialization failure [xxxxxx8A] SCSI card initialization failure [xxxxxx83] SCSI card initialization failure An error has occurred while the driver was setting up its internal data structures. Verify that your SCSI card is supported by this version of the driver. [xxxxx089] Unable to allocate memory This indicates that there may be a problem with the amount of memory installed in your system. Verify that your system has at least the minimum amount of memory required by your operating system. [xxxxx096] SCSI card hardware initialization failure-possible resource conflict The driver has attempted to initialize the SCSI card hardware but failed. This might suggest that an SCSI card resource (for example, an IRQ) conflicts with another board installed in your system. [xxxxx097] Unable to allocate memory This indicates that there may be a problem with the amount of memory installed in your system. Verify that your system has at least the minimum amount of memory required by your operating system. [xxxxx0af] Unable to de-allocate memory that was allocated for a target device Normally, this is not a serious problem, unless you get this message frequently over a short period of time. The memory can be reclaimed by rebooting the system. [xxxxx0ce] Scatter/Gather limit exceeded An I/O request packet from the system contained a Scatter/Gather element list that contained more elements than are supported by the miniport. Scatter/Gather is a list of data segments that define the entire data transfer. Scatter/Gather is a means to improve total data throughput. This error might be caused by a component external to the miniport driver, such as the operating system or an ASPI application. [xxxxxd4] SCSI card hardware failure - SCSI card reset The SCSI card hardware failed and the miniport driver has to reset the hardware. [xxxxx0d6] Internal driver error An error has occurred while the driver was setting up its internal data structures. Try installing the most up-to-date version of the driver available from the Adaptec Web site, www.adaptec.com. Windows Error Messages Error messages generated by the Windows driver can be viewed by opening the Windows Event Viewer error logs.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
Chapter D: Troubleshooting
●
59
[xxxxx081] SCSI card initialization failure
[xxxxxx8A] SCSI card initialization failure
[xxxxxx83] SCSI card initialization failure
An error has occurred while the driver was setting up its internal data structures. Verify that
your SCSI card is supported by this version of the driver.
[xxxxx089] Unable to allocate memory
This indicates that there may be a problem with the amount of memory installed in your
system. Verify that your system has at least the minimum amount of memory required by your
operating system.
[xxxxx096] SCSI card hardware initialization failure—possible resource conflict
The driver has attempted to initialize the SCSI card hardware but failed. This might suggest
that an SCSI card resource (for example, an IRQ) conflicts with another board installed in your
system.
[xxxxx097] Unable to allocate memory
This indicates that there may be a problem with the amount of memory installed in your
system. Verify that your system has at least the minimum amount of memory required by your
operating system.
[xxxxx0af] Unable to de-allocate memory that was allocated for a target device
Normally, this is not a serious problem, unless you get this message frequently over a short
period of time. The memory can be reclaimed by rebooting the system.
[xxxxx0ce] Scatter/Gather limit exceeded
An I/O request packet from the system contained a Scatter/Gather element list that contained
more elements than are supported by the miniport. Scatter/Gather is a list of data segments
that define the entire data transfer. Scatter/Gather is a means to improve total data throughput.
This error might be caused by a component external to the miniport driver, such as the
operating system or an ASPI application.
[xxxxxd4] SCSI card hardware failure - SCSI card reset
The SCSI card hardware failed and the miniport driver has to reset the hardware.
[xxxxx0d6] Internal driver error
An error has occurred while the driver was setting up its internal data structures. Try installing
the most up-to-date version of the driver available from the Adaptec Web site,
www.adaptec.com.
Windows Error Messages
Error messages generated by the Windows driver can be viewed by opening the Windows
Event Viewer error logs.