AEG TR848P4B User Manual - Page 20

Hints And Tips

Page 20 highlights

20 www.aeg.com 3. Remove the laundry. 4. Close the appliance door. Possible causes of unsatisfactory drying results: • Inadequate default dryness level settings. See chapter Adjustment of default dryness level • Room temperature is too low or too high. Optimal room temperature is between 18°-25°C. 8.12 Drum light on 3s 3s 3s Touch and hold down Silent button by around 3 seconds. The light inside the drum is on. 8.13 Possible causes of unsatisfactory drying results: • The filter is clogged. Clogged filter makes drying inefficient. • The airflow slots are clogged. • The humidity sensor is dirty. • The drum is dirty. • Inadequate default dryness level settings. See chapter Adjustment of default dryness level • Room temperature is too low or too high. Optimal room temperature is between 18°-25°C. 9. HINTS AND TIPS 9.1 Ecological hints • Spin the laundry well before drying. • Do not exceed the load sizes which are specified in the programmes chapter. • Clean the filter after each drying cycle. • Do not use fabric softener to wash and then dry. In the tumble dryer laundry becomes soft automatically. • The water from the water container can be used to iron the clothes. You must first filter the water to eliminate remaining textile fibres (simple coffee filter is suitable). • Always keep the airflow slots at the bottom of the appliance clear. • Make sure there is good airflow where the appliance is to be installed. 9.2 Adjustment of default dryness level To change the default dryness level: 1. Turn the appliance on. 2. Select 1 of the available programmes. 3. Touch and hold down the Time Dry and + Anti Crease buttons at the same time. One of the symbols appears on the display: - Maximum dryness - Extra dryness - Standard dryness 4. Touch the Start/Pause button repeatedly until you reach the desired dryness level. Dryness level Display symbol Maximum dryness Extra dry‐ ness Standard dryness 5. To memorise the setting touch and hold down the Time Dry and + Anti Crease buttons at the same time for approximately 2 seconds.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36

3.
Remove the laundry.
4.
Close the appliance door.
Possible causes of unsatisfactory drying
results:
Inadequate default dryness level
settings. See chapter
Adjustment of
default dryness level
Room temperature is too low or too
high. Optimal room temperature is
between 18°-25°C.
8.12 Drum light on
3s
3s
3s
Touch and hold down Silent button by
around 3 seconds.
The light inside the drum is on.
8.13 Possible causes of
unsatisfactory drying results:
The filter is clogged. Clogged filter
makes drying inefficient.
The airflow slots are clogged.
The humidity sensor is dirty.
The drum is dirty.
Inadequate default dryness level
settings. See chapter
Adjustment of
default dryness level
Room temperature is too low or too
high. Optimal room temperature is
between 18°-25°C.
9. HINTS AND TIPS
9.1 Ecological hints
Spin the laundry well before drying.
Do not exceed the load sizes which
are specified in the programmes
chapter.
Clean the filter after each drying
cycle.
Do not use fabric softener to wash
and then dry. In the tumble dryer
laundry becomes soft automatically.
The water from the water container
can be used to iron the clothes. You
must first filter the water to eliminate
remaining textile fibres (simple coffee
filter is suitable).
Always keep the airflow slots at the
bottom of the appliance clear.
Make sure there is good airflow where
the appliance is to be installed.
9.2 Adjustment of default
dryness level
To change the default dryness level:
1.
Turn the appliance on.
2.
Select 1 of the available
programmes.
3.
Touch and hold down the
Time Dry
and
+ Anti Crease
buttons at the
same time.
One of the symbols appears on the
display:
- Maximum dryness
- Extra dryness
- Standard dryness
4.
Touch the
Start/Pause
button
repeatedly until you reach the
desired dryness level.
Dryness
level
Display symbol
Maximum
dryness
Extra dry‐
ness
Standard
dryness
5.
To memorise the setting touch and
hold down the
Time Dry
and
+ Anti
Crease
buttons at the same time for
approximately 2 seconds.
www.aeg.com
20