2012 Yamaha Motorsports FX Nytro RTX Owners Manual - Page 30

2012 Yamaha Motorsports FX Nytro RTX Manual

Get 2012 Yamaha Motorsports FX Nytro RTX PDF manuals and user guides View all 2012 Yamaha Motorsports FX Nytro RTX manuals

Page 30 highlights

Control functions 1. Hose connector 1. Bleed valve button TIP If the shock absorber has no air pressure, the gauge reading will be zero. 5. To increase the air pressure, operate the pump a few times. The pressure should increase slowly. If the pressure increases rapidly, check to make sure that the pump is properly connected and tightened onto the air valve. To decrease the air pressure, push the black bleed valve button. NOTICE: Do not exceed 1034 kPa (10.3 kgf/cm², 150 psi). [ECS00733] Air pressure range: FX10RTRS 345-1034 kPa (3.5-10.3 kgf/cm², 50-150 psi) Recommended air pressure: FX10RTRS 621 kPa (6.2 kgf/cm², 90 psi) TIP To allow pressure to escape from the pump and the shock absorber, push the button halfway down and hold it. To allow only a small amount of pressure to escape, push the button all the way down and quickly release it. 6. Remove the hose connector from the air valve. TIP When removing the connector, the sound of air escaping may be heard, but this is from the pump hose, not the shock absorber. 7. Install the air valve cap. TIP If the front shock absorber bottoms too easily or rolls too much during cornering, increase the air pressure by 34 kPa (0.3 kgf/cm², 5 psi). If the shock absorber is too firm and you want a more compliant ride, decrease the air pressure by 34 kPa (0.3 kgf/cm², 5 psi). 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
Control functions
24
TIP
If the shock absorber has no air pressure, the
gauge reading will be zero.
5.
To increase the air pressure, operate the
pump a few times. The pressure should
increase slowly. If the pressure increases
rapidly, check to make sure that the
pump is properly connected and tight-
ened onto the air valve. To decrease the
air pressure, push the black bleed valve
button.
NOTICE:
Do not exceed 1034
kPa (10.3 kgf/cm², 150 psi).
[ECS00733]
TIP
To allow pressure to escape from the pump
and the shock absorber, push the button half-
way down and hold it. To allow only a small
amount of pressure to escape, push the but-
ton all the way down and quickly release it.
6.
Remove the hose connector from the air
valve.
TIP
When removing the connector, the sound of
air escaping may be heard, but this is from the
pump hose, not the shock absorber.
7.
Install the air valve cap.
TIP
If the front shock absorber bottoms too easily
or rolls too much during cornering, increase
the air pressure by 34 kPa (0.3 kgf/cm², 5 psi).
If the shock absorber is too firm and you want
a more compliant ride, decrease the air pres-
sure by 34 kPa (0.3 kgf/cm², 5 psi).
1.
Hose connector
1.
Bleed valve button
Air pressure range:
FX10RTRS 345–1034 kPa (3.5–10.3
kgf/cm², 50–150 psi)
Recommended air pressure:
FX10RTRS 621 kPa (6.2 kgf/cm², 90
psi)