2011 Yamaha Motorsports V Star 250 Owners Manual - Page 49

2011 Yamaha Motorsports V Star 250 Manual

Get 2011 Yamaha Motorsports V Star 250 PDF manuals and user guides View all 2011 Yamaha Motorsports V Star 250 manuals

Page 49 highlights

PERIODIC MAINTENANCE AND ADJUSTMENT Tightening torque: Engine oil drain bolt: 34 Nm (3.4 m·kgf, 25 ft·lbf) 8. Refill with the specified amount of the recommended engine oil, and then install and tighten the oil filler cap. 1. Oil filter element 2. O-ring G fication of "CD" or oils of a higher quality than specified. In addition, do not use oils labeled "ENERGY CONSERVING II" or higher. Make sure that no foreign material enters the crankcase. 6. Install the oil filter element cover by installing the screws, then tightening them to the specified torque. Tightening torque: Oil filter element cover screw: 10 Nm (1.0 m·kgf, 7.2 ft·lbf) Recommended engine oil: See page 9-1. Oil quantity: With oil filter element replacement: 1.60 L (1.69 US qt, 1.41 Imp.qt) Without oil filter element replacement: 1.40 L (1.48 US qt, 1.23 Imp.qt) 9. Start the engine, and then let it idle for several minutes while checking it for oil leakage. If oil is leaking, immediately turn the engine off and check for the cause. 10. Turn the engine off, and then check the oil level and correct it if necessary. 7 TIP Make sure that the O-ring is properly seated. 7. Install the engine oil drain bolt and its new gasket, and then tighten the bolt to the specified torque. TIP Be sure to wipe off spilled oil on any parts after the engine and exhaust system have cooled down. ECA11620 NOTICE G In order to prevent clutch slippage (since the engine oil also lubricates the clutch), do not mix any chemical additives. Do not use oils with a diesel speci7-13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
PERIODIC MAINTENANCE AND ADJUSTMENT
7-13
7
6.
Install the oil filter element cover by
installing the screws, then tighten-
ing them to the specified torque.
TIP
Make sure that the O-ring is properly
seated.
7.
Install the engine oil drain bolt and
its new gasket, and then tighten
the bolt to the specified torque.
8.
Refill with the specified amount of
the recommended engine oil, and
then install and tighten the oil filler
cap.
TIP
Be sure to wipe off spilled oil on any
parts after the engine and exhaust sys-
tem have cooled down.
NOTICE
ECA11620
●
In order to prevent clutch slip-
page (since the engine oil also
lubricates the clutch), do not
mix any chemical additives. Do
not use oils with a diesel speci-
fication of “CD” or oils of a high-
er quality than specified. In
addition, do not use oils labeled
“ENERGY CONSERVING II” or
higher.
●
Make sure that no foreign mate-
rial enters the crankcase.
9.
Start the engine, and then let it idle
for several minutes while checking
it for oil leakage. If oil is leaking, im-
mediately turn the engine off and
check for the cause.
10. Turn the engine off, and then
check the oil level and correct it if
necessary.
1.
Oil filter element
2. O-ring
Tightening torque:
Oil filter element cover screw:
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
Tightening torque:
Engine oil drain bolt:
34 Nm (3.4 m·kgf, 25 ft·lbf)
Recommended engine oil:
See page 9-1.
Oil quantity:
With oil filter element replacement:
1.60 L (1.69 US qt, 1.41 Imp.qt)
Without oil filter element replace-
ment:
1.40 L (1.48 US qt, 1.23 Imp.qt)