2008 Yamaha Motorsports C3 Owners Manual - Page 52

2008 Yamaha Motorsports C3 Manual

Get 2008 Yamaha Motorsports C3 PDF manuals and user guides View all 2008 Yamaha Motorsports C3 manuals

Page 52 highlights

Fuse, replacing PERIODIC MAINTENANCE AND MINOR REPAIR Remove panel C to access the battery. (See page 6-6.) 1 2 3 4 5 6 7 8 9 To charge the battery Have a Yamaha dealer charge the battery as soon as possible if it seems to have discharged. Keep in mind that the battery tends to discharge more quickly if the vehicle is equipped with optional electrical accessories. To store the battery 1. If the vehicle will not be used for more than one month, remove the battery, fully charge it, and then place it in a cool, dry place. 2. If the battery will be stored for more than two months, check it at least once a month and fully charge it if necessary. 3. Fully charge the battery before installation. 4. After installation, make sure that the battery leads are properly connected to the battery terminals. ECAT1051 EAU17226 ● ● charged. Storing a discharged battery can cause permanent battery damage. To charge a sealed-type (MF) battery, a special (constant-voltage) battery charger is required. Using a conventional battery charger will damage the battery. If you do not have access to a sealed-type (MF) battery charger, have a Yamaha dealer charge your battery. After installing the battery, be sure to turn the main switch from "ON" to "OFF" three times in 3 seconds intervals to initialize the idle speed control system. EAUT2021 Replacing the fuse 1 ZAUM00** 1. Fuse The fuse holder is located beside the battery. Remove panel C to access the fuse. (See page 6-6.) If the fuse is blown, replace it as follows. 1. Turn the key to "OFF" and turn off all electrical circuits. 2. Remove the blown fuse, and then install a new fuse of the specified amperage. Specified fuse: 15 A cC ● Always keep the battery 6-21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
6-21
1
2
3
4
5
6
7
8
9
EAU17226
PERIODIC MAINTENANCE AND MINOR REPAIR
Remove panel C to access the battery.
(See page 6-6.)
To charge the battery
Have a Yamaha dealer charge the bat-
tery as soon as possible if it seems to
have discharged. Keep in mind that the
battery tends to discharge more quickly
if the vehicle is equipped with optional
electrical accessories.
To store the battery
1.
If the vehicle will not be used for
more than one month, remove the
battery, fully charge it, and then
place it in a cool, dry place.
2.
If the battery will be stored for more
than two months, check it at least
once a month and fully charge it if
necessary.
3.
Fully charge the battery before in-
stallation.
4. After installation, make sure that
the battery leads are properly con-
nected to the battery terminals.
ECAT1051
c
C
●
Always keep the battery
charged. Storing a discharged
battery can cause permanent
battery damage.
●
To charge a sealed-type (MF)
battery, a special (constant-volt-
age) battery charger is required.
Using a conventional battery
charger will damage the battery.
If you do not have access to a
sealed-type
(MF)
battery
charger, have a Yamaha dealer
charge your battery.
●
After installing the battery, be
sure to turn the main switch
from “ON” to “OFF” three times
in 3 seconds intervals to initial-
ize the idle speed control sys-
tem.
EAUT2021
Replacing the fuse
ZAUM00**
1
1. Fuse
The fuse holder is located beside the
battery. Remove panel C to access the
fuse. (See page 6-6.)
If the fuse is blown, replace it as follows.
1.
Turn the key to “OFF” and turn off
all electrical circuits.
2.
Remove the blown fuse, and then
install a new fuse of the specified
amperage.
Specified fuse:
15 A
Fuse, replacing<IXE>