2003 Yamaha Motorsports RX-1 Owners Manual - Page 64

2003 Yamaha Motorsports RX-1 Manual

Get 2003 Yamaha Motorsports RX-1 PDF manuals and user guides View all 2003 Yamaha Motorsports RX-1 manuals

Page 64 highlights

Tightening torques: Crankcase engine oil drain bolt: 30 Nm (3.0 m·kgf, 22 ft·lb) Oil tank engine oil drain bolt: 16 Nm (1.6 m·kgf, 11 ft·lb) 8. Add 2.0 L (1.8 Imp qt, 2.1 US qt) of the recommended engine oil to the oil tank, and then install and tighten the oil level gauge/dipstick and the cylinder head cap. Recommended engine oil: See page 6-2. Oil quantity: With oil filter cartridge replacement: 3.0 L (2.6 Imp qt, 3.2 US qt) Without oil filter cartridge replacement: 2.8 L (2.5 Imp qt, 3.0 US qt) Total amount: 3.8 L (3.3 Imp qt, 4.0 US qt) 9. Start the engine, warm it up for several minutes, and then turn it off. 10. Add sufficient oil of the recommended type to raise it to the "F" level mark on the oil level gauge/dipstick. (See page 6-3 for checking procedure.) CAUTION: @ G G @ When adding the engine oil, be careful not to fill above the "F" level mark on the oil level gauge/ dipstick. Make sure that no foreign material enters the engine oil tank. 11. Start the engine, and then let it idle for several minutes while checking it for oil leakage. If oil is leaking, immediately turn the engine off and make sure the engine oil drain bolts and oil level gauge/dipstick are installed correctly. 12. Turn the engine off, and then install the bottom cover and right side cover. CAUTION: @ If oil is leaking or the oil level warning indicator comes on when the engine is running, immediately turn the engine off and have a Yamaha dealer check the snowmobile. Continuing to operate the engine under such conditions could cause severe engine damage. @ 8-12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
8-12
8. Add 2.0 L (1.8 Imp qt, 2.1 US qt) of the recommended
engine oil to the oil tank, and then install and tighten
the oil level gauge/dipstick and the cylinder head cap.
9. Start the engine, warm it up for several minutes, and
then turn it off.
10. Add sufficient oil of the recommended type to raise it
to the “F” level mark on the oil level gauge/dipstick.
(See page 6-3 for checking procedure.)
CAUTION
:
@
●
When adding the engine oil, be careful not to fill
above the “F” level mark on the oil level gauge/
dipstick.
●
Make sure that no foreign material enters the
engine oil tank.
@
11. Start the engine, and then let it idle for several min-
utes while checking it for oil leakage. If oil is leaking,
immediately turn the engine off and make sure the
engine oil drain bolts and oil level gauge/dipstick are
installed correctly.
12. Turn the engine off, and then install the bottom cover
and right side cover.
CAUTION
:
@
If oil is leaking or the oil level warning indicator comes
on when the engine is running, immediately turn the
engine off and have a Yamaha dealer check the snow-
mobile. Continuing to operate the engine under such
conditions could cause severe engine damage.
@
Tightening torques:
Crankcase engine oil drain bolt:
30 Nm (3.0 m·kgf, 22 ft·lb)
Oil tank engine oil drain bolt:
16 Nm (1.6 m·kgf, 11 ft·lb)
Recommended engine oil:
See page 6-2.
Oil quantity:
With oil filter cartridge replacement:
3.0 L (2.6 Imp qt, 3.2 US qt)
Without oil filter cartridge replacement:
2.8 L (2.5 Imp qt, 3.0 US qt)
Total amount:
3.8 L (3.3 Imp qt, 4.0 US qt)