2002 Yamaha Motorsports Beartracker Owners Manual - Page 121

2002 Yamaha Motorsports Beartracker Manual

Get 2002 Yamaha Motorsports Beartracker PDF manuals and user guides View all 2002 Yamaha Motorsports Beartracker manuals

Page 121 highlights

WARNING POTENTIAL HAZARD Using low flash point solvents or gasoline to clean the foam cover. WHAT CAN HAPPEN Low flash point solvents or gasoline can catch fire or explode. HOW TO AVOID THE HAZARD Use parts cleaning solvent to clean the foam cover. 7. Squeeze the excess water or solvent out of the foam cover and let it dry. 10. Install the air filter assembly and parts removed for access. NOTE: The air filter element should be cleaned every 20 ~ 40 hours. It should be cleaned more often if the machine is operated in extremely dusty areas. Each time filter element maintenance is performed, check the air inlet to the filter case for obstructions. Check the air cleaner rubber joint to the carburetor and manifold fittings for an airtight seal. Tighten all fittings securely to avoid the possibility of unfiltered air entering the engine. _ _ CAUTION: _ _ CAUTION: Never operate the engine with the air filter element removed. This will allow unfiltered air to enter, causing rapid engine wear and possible engine damage. Additionally, operation without the filter element will affect carburetor jetting with subsequent poor performance and possible engine overheating. 8-14 _ ● ● _ Do not twist the foam cover when squeezing it. Do not apply oil to the foam cover. 8. Inspect the foam cover. If damaged, replace it. 9. Install the foam cover onto the air filter element.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
8-14
7.
Squeeze the excess water or solvent out
of the foam cover and let it dry.
CAUTION:
_
●
Do not twist the foam cover when
squeezing it.
●
Do not apply oil to the foam cover.
_
8.
Inspect the foam cover. If damaged, re-
place it.
9.
Install the foam cover onto the air filter el-
ement.
10.
Install the air filter assembly and parts re-
moved for access.
NOTE:
_
The air filter element should be cleaned every
20 ~ 40 hours. It should be cleaned more of-
ten if the machine is operated in extremely
dusty areas. Each time filter element mainte-
nance is performed, check the air inlet to the
filter case for obstructions. Check the air
cleaner rubber joint to the carburetor and
manifold fittings for an airtight seal. Tighten all
fittings securely to avoid the possibility of unfil-
tered air entering the engine.
_
CAUTION:
_
Never operate the engine with the air filter
element removed. This will allow unfiltered
air to enter, causing rapid engine wear and
possible engine damage. Additionally, op-
eration without the filter element will affect
carburetor jetting with subsequent poor
performance and possible engine over-
heating.
_
WARNING
POTENTIAL HAZARD
Using low flash point solvents or gaso-
line to clean the foam cover.
WHAT CAN HAPPEN
Low flash point solvents or gasoline can
catch fire or explode.
HOW TO AVOID THE HAZARD
Use parts cleaning solvent to clean the
foam cover.