Zanussi ZWF824B3PW User Manual - Page 4
Electrical Connection, Warning, Water Connection, Service
View all Zanussi ZWF824B3PW manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 4 highlights
• Do not install or use the appliance where the temperature can be less than 0°C or where it is exposed to the weather. • The floor area on which the appliance is to be installed must be flat, stable, heat resistant and clean. • Make sure that there is air circulation between the appliance and the floor. • When the appliance is in its permanent position, check if it is levelled correctly with the aid of a spirit level. If it is not, adjust the feet accordingly. • Do not install the appliance directly above a floor drain. • Do not spray water on the appliance and do not expose it to excessive humidity. • Do not install the appliance where the appliance door cannot be fully opened. • Do not put a closed container to collect possible water leakage under the appliance. Contact the Authorised Service Centre to ensure which accessories can be used. ELECTRICAL CONNECTION WARNING! Risk of fire and electric shock. • WARNING: This appliance is designed to be installed / connected to a grounding connection in the building. • Always use a correctly installed shockproof socket. • Make sure that the parameters on the rating plate are compatible with the electrical ratings of the mains power supply. • Do not use multi-plug adapters and extension cables. • Make sure not to cause damage to the mains plug and to the mains cable. Should the mains cable need to be replaced, this must be carried out by our Authorised Service Centre. • Connect the mains plug to the mains socket only at the end of the installation. Make sure that there is access to the mains plug after the installation. • Do not touch the mains cable or the mains plug with wet hands. • Do not pull the mains cable to disconnect the appliance. Always pull the mains plug. • This appliance is fitted with a 13 A mains plug. If it is necessary to change the mains plug fuse, use only a 13 A ASTA (BS 1362) fuse (UK and Ireland only). WATER CONNECTION • The inlet water shall not exceed 25 °C. • Do not cause damage to the water hoses. • Before connection to new pipes, pipes not used for a long time, where repair work has been carried out or new devices fitted (water meters, etc.), let the water flow until it is clean and clear. • Ensure that there are no visible water leaks during and after the first use of the appliance. • Do not use an extension hose if the inlet hose is too short. Contact the Authorised Service Centre for the replacement of the inlet hose. • When unpacking the appliance, It is possible to see water flowing from the drain hose. This is due to the testing of the appliance with the use of water in the factory. • You can extend the drain hose to maximum 400 cm. Contact the Authorised Service Centre for the other drain hose and the extension. • Make sure that there is access to the tap after the installation. USE WARNING! Risk of injury, electric shock, fire, burns or damage to the appliance. • Follow the safety instructions on the detergent packaging. • Do not put flammable products or items that are wet with flammable products in, near or on the appliance. • Do not wash fabrics which are heavily soiled with oil, grease or other greasy substances. It can damage rubber parts of the washing machine. Prewash such fabrics by hand before loading them into the washing machine. • Do not touch the glass door while a programme operates. The glass can get hot. • Make sure that all metal objects are removed from the laundry. SERVICE • To repair the appliance contact the Authorised Service Centre. Use original spare parts only. • Please note that self-repair or non-professional repair can have safety consequences and might void the guarantee. • The following spare parts will be available for 10 years after the model has been discontinued: motor and motor brushes, transmission between motor and drum, pumps, shock absorbers and springs, washing drum, drum spider and related ball bearings, heaters and heating elements, including heat pumps, piping and related equipment including hoses, valves, filters and aquastops, printed circuit boards, electronic displays, pressure switches, thermostats and sensors, software and firmware including reset software, door, door hinge and seals, other 4