Zanussi ZW74PDBI User Manual - Page 35

Troubleshooting

Get Zanussi ZW74PDBI PDF manuals and user guides View all Zanussi ZW74PDBI manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

EMERGENCY DRAIN If the appliance cannot drain the water, carry out the same procedure, described in 'Cleaning the drain pump' paragraph. If necessary, clean the pump. When you drain the water with the emergency drain procedure, you must activate the drain system again: 1. Put 2 litres of water in the main wash compartment of the detergent dispenser. 2. Start the programme to drain the water. FROST PRECAUTIONS If the appliance is installed in an area where the temperature can reach values around 0° C or drop below, remove the remaining water from the inlet hose and the drain pump. TROUBLESHOOTING 1. Disconnect the mains plug from the mains socket. 2. Close the water tap. 3. Put the two ends of the inlet hose in a container and let the water flow out of the hose. 4. Empty the drain pump. Refer to the emergency drain procedure. 5. When the drain pump is empty, install the inlet hose again. WARNING! Make sure that the temperature is higher than 0 °C before you use the appliance again. The manufacturer is not responsible for damages caused by low temperatures. WARNING! Refer to Safety chapters. ALARM CODES AND POSSIBLE FAILURES The appliance does not start or it stops during operation. First try to find a solution to the problem (refer to the tables). WARNING! Deactivate the appliance before carrying out any check. With some problems, the display shows an alarm code and the Start/ Pause button may flash continuously: If the appliance is overloaded, remove some items from the drum and/or keep pressed the door while touching the Start/Pause button until the indicator stops flashing (see the picture below). Problem Possible solution 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
EMERGENCY DRAIN
If the appliance cannot drain the water, carry out
the same procedure, described in 'Cleaning the
drain pump' paragraph. If necessary, clean the
pump.
When you drain the water with the emergency drain
procedure, you must activate the drain system
again:
1.
Put 2 litres of water in the main wash
compartment of the detergent dispenser.
2.
Start the programme to drain the water.
FROST PRECAUTIONS
If the appliance is installed in an area where the
temperature can reach values around 0° C or drop
below, remove the remaining water from the inlet
hose and the drain pump.
1.
Disconnect the mains plug from the mains
socket.
2.
Close the water tap.
3.
Put the two ends of the inlet hose in a
container and let the water
flow
out of the
hose.
4.
Empty the drain pump. Refer to the emergency
drain procedure.
5.
When the drain pump is empty, install the inlet
hose again.
WARNING!
Make sure that the
temperature is higher than 0 °C before
you use the appliance again.
The manufacturer is not responsible
for damages caused by low
temperatures.
TROUBLESHOOTING
WARNING!
Refer to Safety chapters.
ALARM CODES AND POSSIBLE FAILURES
The appliance does not start or it stops during operation. First try to
find
a solution to the problem (refer to
the tables).
WARNING!
Deactivate the appliance before carrying out any check.
With some problems, the display shows an alarm code and the
Start/
Pause
button may
flash
continuously:
If the appliance is overloaded, remove some items from the drum
and/or keep pressed the door while touching the Start/Pause but-
ton until the indicator
stops
flashing
(see the picture below).
Problem
Possible solution
35