Whirlpool EDR1RXD1 Performance Data Sheet - Page 2

Linuron Estrone Nonylphenol Carbamazepine Phenytoin Naproxen Bisphenol A 140 ± 20% 140 ± 20% 1400 ± 20% 1400 ± 20% 200 ± 20% 140 ± 20% 2000 ± 20% 20 ng/L 20 ng/L 200 ng/L 200 ng/L 30 ng/L 20 ng/L 300 ng/L >97.9% 93.8% 96.1% 99.20% 99.3% / 98.6.% 93.3% 98.9% Test Parameters: pH = 7.5 ± 0.5 unless otherwise noted. Flow = 0.5 gpm (1.89 lpm). Pressure = 60 psig (413.7 kPa). Temp. = 68°F to 71.6°F (20°C to 22°C). Rated service capacity = 200 gallons (757 liters). The compounds certified under NSF 401 have been deemed as "emerging compounds/incidental contaminants." Emerging compounds/incidental contaminants are those compounds that have been detected in drinking water supplies at trace levels. While occurring at only trace levels, these compounds can affect the public acceptance/perception of drinking water quality. � For installation, operation, and maintenance instructions please � The product is for cold water use only. refer to the Owner's Manual. � It is important that operational, maintenance, and filter � The water system must be installed in compliance with state and local laws and regulations. replacement requirements be carried out for the product to perform as advertised. Property damage can occur if all instructions � are not followed. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on � The disposable cartridge must be changed at least every 6 months. disinfected waters that may contain filterable cysts. EPA Est. No. � Use replacement filter part #EDR1RXD1/EDR1RXD1B. 2015 suggested retail price of $49.99 U.S.A./$49.99 Canada. Prices are 082047-TWN-001 � Refer to the "Warranty" section (in the User Instructions or User subject to change without notice. Guide) for the Manufacturer's limited warranty, name and � The filter monitor system measures the amount of water that telephone number. passes through the filter and alerts you when it is time to replace the filter. Application Guidelines/Water Supply Parameters � Refer to the "Using the Controls" or "Water Filtration System" section (in the User Instructions or User Guide) to learn how to check the water filter status. Water Supply Water Pressure Potable City or Well 30 psi - 120 psi (207 kPa - 827 kPa) � After changing the water filter, flush the water system. See "Water and Ice Dispensers" or "Water Dispenser" in the User Instructions or User Guide. Water Temperature Service Flow Rate 33° - 100°F (0.6° - 37.8° C) 0.50 GPM (2.27 L/min.) @ 60 psi. (413.7 kPa) � These contaminants are not necessarily in your water supply. While � testing was performed under standard laboratory conditions, actual performance may vary. Your water filtration system will withstand up to 120 pounds per square inch (psi) water pressure. If your water supply is higher than 80 psi, install a pressure reducing valve before installing the � For installation, operation and maintenance instructions please water filtration system. refer Owner's Manual. Consumer Support 1.800.442.9991 By Whirlpool Corporation 2000 North M63 Benton Harbor, MI 49022 Made in Taiwan. *Class I particle size: >0.5 to 1 um †Based on the use of Cryptosporidium parvum oocysts ††Fibers greater than 10 um in length ®NSF is a registered trademark of NSF International. 2 10-May-2021 11:18:44 EDT | RELEASED In some European factories the letter "W" of the part code mentioned herein will be automatically replaced by the number "4000" (e.g. "W12345678" becomes "400012345678")