Tripp Lite SR45UBTAA Owner's Manual for Smart Rack Enclosures 932723 - Page 11

Enclosure Configuration, Equipment Installation

Get Tripp Lite SR45UBTAA PDF manuals and user guides View all Tripp Lite SR45UBTAA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Enclosure Configuration Combining (Baying) Enclosures WARNING: Combining enclosures is not a substitute for stabilizing the enclosures. Each enclosure in a bay of combined enclosures requires the same stabilizing measures as a standalone enclosure. 1 Arrange the enclosures in the correct position for baying. 1 2 Each enclosure includes 4 baying brackets A that correspond to baying connection points B on the adjoining enclosure. The baying connection points already contain screws. Remove the screw from each baying connection point in the adjoining enclosure. B A 2 3 Loosen the screw in each baying bracket and turn each bracket 90 degrees toward the adjoining enclosure, aligning each bracket with the corresponding baying connection point on the adjoining enclosure. 3 4 Connect each bracket to the adjoining enclosure using the screws you removed in step 2, but do not tighten the screws completely. Adjust the position of the enclosures as needed. If you want the centers of the enclosures to be 24 inches (61 cm) apart/29.9 inches (76 cm) for the SR42UBWD, use the outside hole of the bracket C . If you want the centers to be 60 cm (23.6 inches) apart/75 cm (29.5 inches) for the SR42UBWD, use the middle hole of the bracket D . After connecting all brackets and confirming that the enclosures do not need further adjustment, tighten all screws. Note: You may wish to remove the doors from the enclosures before combining them. Reinstalling the doors afterward is optional. Remove the interior side panels before baying enclosures if you wish to enable access between enclosures. 4 90° D C 29 Equipment Installation 29 WARNING: Do not install equ28ipment until you have stabilized the enclosure. Install heavier equipment first and install it toward 2t8he bottom of the enclosure. Install equipment starting from the bottom of the enclosure and proceeding toward the top of the enclosure - never the reverse. If using sliding equipment rails, be careful when extending the rails. Do not extend more than one set of sliding equipment rails at one time. Avoid extending sliding equipment rails near the top of the enclosure. 27 27 Note: The square holes at the middle of each rack unit are numbered and also include a small notch to aid identification. A single rack unit includes the space occupied by the numbered hole and the holes directly above and below. 26 26 25 25 24 24 23 1 Rack Unit 23 22 21 201112001_L 93-2723.indd 11 22 11 21 12/14/2011 11:27:29 AM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
11
Enclosure Configuration
Combining (Baying) Enclosures
WARNING: Combining enclosures is not a substitute for stabilizing the enclosures. Each enclosure in a bay of combined enclosures requires the same stabilizing
measures as a standalone enclosure.
1
Arrange the enclosures in the correct position for baying.
2
Each enclosure includes 4 baying brackets
A
that correspond to baying connection points
B
on the
adjoining enclosure. The baying connection points already contain screws. Remove the screw from each
baying connection point in the adjoining enclosure.
3
Loosen the screw in each baying bracket and turn each bracket 90 degrees toward the adjoining enclosure,
aligning each bracket with the corresponding baying connection point on the adjoining enclosure.
4
Connect each bracket to the adjoining enclosure using the screws you removed in step 2, but do not
tighten the screws completely. Adjust the position of the enclosures as needed. If you want the centers of
the enclosures to be 24 inches (61 cm) apart/29.9 inches (76 cm) for the SR42UBWD, use the outside hole
of the bracket
C
. If you want the centers to be 60 cm (23.6 inches) apart/75 cm (29.5 inches) for the
SR42UBWD, use the middle hole of the bracket
D
. After connecting all brackets and confirming that the
enclosures do not need further adjustment, tighten all screws.
Note: You may wish to remove the doors from the enclosures before combining them. Reinstalling the doors
afterward is optional. Remove the interior side panels before baying enclosures if you wish to enable access
between enclosures.
Equipment Installation
WARNING: Do not install equipment until you have stabilized the enclosure. Install heavier equipment first and install it toward the bottom of the enclosure.
Install equipment starting from the bottom of the enclosure and proceeding toward the top of the enclosure - never the reverse. If using sliding equipment rails,
be careful when extending the rails. Do not extend more than one set of sliding equipment rails at one time. Avoid extending sliding equipment rails near the top
of the enclosure.
Note: The square holes at the middle of each rack unit are numbered and also include a small notch to aid identification. A single rack unit includes the space occupied
by the numbered hole and the holes directly above and below.
90°
25
23
22
24
25
23
22
24
24
2
1 Rack Unit
3
4
2
1
C
D
A
B
201112001_L 93-2723.indd
11
12/14/2011
11:27:29 AM