TASCAM CC-222SL Owners Manual - Page 29

Introduction, Cassette operating

Get TASCAM CC-222SL PDF manuals and user guides View all TASCAM CC-222SL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

7 - Cas1se- tItnetroopdeurcattiionng Note the following when loading tapes: 1 Use your finger or a pencil to turn the cassette's hub and take up any slack tape. NOTE Avoid touching the tape. Fingerprints attract dust and dirt. Playback operations WARNING If you are monitoring using headphones, first adjust the level control to low on the unit, then connect to the POHNES jack before playing back. This will prevent any possible damage to your hearing. 1 Set the REV MODE switch to the required tape mode. Ä Single-sided playback Ë One side, then the other side, then stop ä One side, then the other side, then the first side again, etc. Also, check the monitor switch is set to tape. Continuous tape/CD playback 1 Load the tape as described above into the unit. Load the disc recorded side downwards into the unit. 2 Press the CD-TAPE CONT PLAY key. 3 Press either of the PLAY keys of the tape deck or the CD deck. Playback will start on the appropriate unit. When playback reaches the end of the disc, or the end of the tape as determined by the REV MODE setting, playback starts on the other unit. NOTE Media (tape or disc) can be changed in the unit that is not playing. 4 To stop playback and cancel the mode, press the CD-TAPE CONT PLAY key again. 2 Press the EJECT key to open the cassette compartment door. 3 Load the cassette tape with its open edge facing down. 4 Gently close the compartment door. NOTE The cassette holder cannot be opened during recording or playback. If the power has been switched off during play or recording, ejecting the cassette may be impossible. In such a case, switch the power on and press the EJECT key again. 2 Load a pre-recorded cassette with its open edge facing down and side A facing toward you. 3 Set the DOLBY NR system on or off. 4 Press either PLAY key to start playback. 5 Adjust the volume with the amplifier's volume control. 6 To stop playback, press the STOP key. NOTE The cassette deck and CD deck can be used to play back through different outputs, or the LINE OUTPUTS 2 jacks can be used for both disc and tape playback (see "OUT2 setting (TAPE or AUTO)" on page 32 for details). However, note that if both are playing, the cassette takes priority (the disc will not be heard through these outputs). The LINE OUTPUTS1 jacks always output the audio from th edisc. 29 TASCAM CC-222SL

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
1- Introduction
TASCAM
CC-222SL
±¸
Note the following when loading tapes:
1
Use your finger or a pencil to turn the cassette's hub
and take up any slack tape.
NOTE
Avoid touching the tape. Fingerprints attract dust and
dirt.
2
Press the
EJECT
key to open the cassette compart-
ment door.
3
Load the cassette tape with its open edge facing
down.
4
Gently close the compartment door.
NOTE
The cassette holder cannot be opened during record-
ing or playback.
If the power has been switched off during play or
recording, ejecting the cassette may be impossible. In
such a case, switch the power on and press the EJECT
key again.
Continuous tape/CD playback
1
Load the tape as described above into the unit.
Load the disc recorded side downwards into the
unit.
2
Press the
CD-TAPE CONT PLAY
key.
3
Press either of the
PLAY
keys of the tape deck or the
CD deck.
Playback will start on the appropriate unit. When
playback reaches the end of the disc, or the end of
the tape as determined by the
REV MODE
setting,
playback starts on the other unit.
NOTE
Media (tape or disc) can be changed in the unit that is
not playing.
4
To stop playback and cancel the mode, press the
CD-TAPE CONT PLAY
key again.
NOTE
The cassette deck and CD deck can be used to play
back through different outputs, or the LINE OUTPUTS
2 jacks can be used for both disc and tape playback
(see “OUT2 setting (TAPE or AUTO)” on page 32 for
details). However, note that if both are playing, the
cassette takes priority (the disc will not be heard
through these outputs).
The LINE OUTPUTS1 jacks always output the audio
from th edisc.
Playback operations
WARNING
If you are monitoring using headphones, first adjust
the level control to low on the unit, then connect to the
POHNES jack before playing back. This will prevent
any possible damage to your hearing.
1
Set the
REV MODE
switch to the required tape
mode.
Ä
Single-sided playback
Ë
One side, then the other side, then stop
ä
One side, then the other side, then the first side
again, etc.
Also, check the
MONITOR
switch is set to
TAPE
.
2
Load a pre-recorded cassette with its open edge fac-
ing down and side A facing toward you.
3
Set the
DOLBY NR
system on or off.
4
Press either
PLAY
key to start playback.
5
Adjust the volume with the amplifier’s volume control.
6
To stop playback, press the
STOP
key.
7 – Cassette operating