Stihl TS 800 STIHL Cutquik174 Product Instruction Manual - Page 22

Cutting wheels, Composite resin cutting, wheels

Get Stihl TS 800 STIHL Cutquik174 PDF manuals and user guides View all Stihl TS 800 STIHL Cutquik174 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

English 12 N Always make severing cuts so that the abrasive wheel is not pinched. N Use wedges and/or leave ridges that are broken after cutting. 4 3 N If the severed part remains in the recess after cutting (due to wedges, ridges used), do not make any further cuts - break the severed part. 180BA026 AM 180BA025 AM 180BA024 AM Cutting wheels Cutting wheels are exposed to extremely high loads especially during hand-held cutting. Only use abrasive whhels that comply with ANSI B 7.1 for hand-held machines and are correspondingly labeled. Note that the maximum permissible speed of the cutting wheel must be higher than the maximum spindle speed listed on the wheel guard label. The cutting wheels that have been developed for STIHL by well-known manufacturers of abrasive wheels are of high quality and tailored precisely to the respective intended use as well as the engine performance of the cut-off machine. Transport and storage - Do not expose cutting wheels to direct sunshine or other thermal stresses during transport and storage. - Avoid jolting and impacts. - Stack cutting wheels flat on a level surface in the original packaging in a dry place where the temperature is as constant as possible. - Do not store cutting wheels in the vicinity of aggressive fluids. - Store cutting wheels in a frost-free place. Composite resin cutting wheels Types: - for dry applications - for wet applications Economic benefit is improved and premature wear can be avoided by choosing and using the correct composite resin cutting wheel. The short name (e.g. "asphalt", "concrete") - on the label and - on the packaging (table with recommended uses) can help to ensure the correct choice. STIHL composite resin cutting wheels are suitable, depending on the version, for cutting the following materials: - Asphalt - Concrete - Stone - Ductile cast pipes - Steel; STIHL composite resin cutting wheels cannot be used to cut railway tracks. Do not cut any other materials - risk of accident! 20 TS 700, TS 800

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
TS 700, TS 800
English
20
N
Always make severing cuts so that
the abrasive wheel is not pinched.
N
Use wedges and/or leave ridges
that are broken after cutting.
N
If the severed part remains in the
recess after cutting (due to wedges,
ridges used), do not make any
further cuts – break the severed
part.
Cutting wheels are exposed to
extremely high loads especially during
hand-held cutting.
Only use abrasive whhels that comply
with ANSI
B
7.1 for hand-held machines
and are correspondingly labeled. Note
that the maximum permissible speed of
the cutting wheel must be higher than
the maximum spindle speed listed on
the wheel guard label.
The cutting wheels that have been
developed for STIHL by well-known
manufacturers of abrasive wheels are of
high quality and tailored precisely to the
respective intended use as well as the
engine performance of the cut-off
machine.
Transport and storage
–
Do not expose cutting wheels to
direct sunshine or other thermal
stresses during transport and
storage.
–
Avoid jolting and impacts.
–
Stack cutting wheels flat on a level
surface in the original packaging in
a dry place where the temperature
is as constant as possible.
–
Do not store cutting wheels in the
vicinity of aggressive fluids.
–
Store cutting wheels in a frost-free
place.
Types:
–
for dry applications
–
for wet applications
Economic benefit is improved and
premature wear can be avoided by
choosing and using the correct
composite resin cutting wheel. The short
name (e.g. “asphalt“, “concrete“)
–
on the label and
–
on the packaging (table with
recommended uses)
can help to ensure the correct choice.
STIHL composite resin cutting wheels
are suitable, depending on the version,
for cutting the following materials:
–
Asphalt
–
Concrete
–
Stone
–
Ductile cast pipes
–
Steel; STIHL composite resin
cutting wheels cannot be used to cut
railway tracks.
Do not cut any other materials –
risk of
accident!
1
2
180BA024 AM
180BA025 AM
180BA026 AM
3
4
Cutting wheels
Composite resin cutting
wheels