Home » Stihl Manuals » Lawn & Garden » Stihl RE 100 PLUS CONTROL » Manual Viewer

Stihl RE 100 PLUS CONTROL Instruction Manual - Page 35

Troubleshooting Guide

Get Stihl RE 100 PLUS CONTROL PDF manuals and user guides

View all Stihl RE 100 PLUS CONTROL manuals

Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

18 Troubleshooting Guide 18 Troubleshooting Guide English 18.1 Pressure Washer Before troubleshooting, switch off the pressure washer and disconnect the unit from the power supply. Relieve all system pressure by pulling the trigger switch. Lock the spray gun trigger. Condition The pressure washer does not start although the spray gun trigger is pulled. The pressure washer does not start when switched on. The electric motor hums. The pressure washer switches off while in operation. The high-pressure pump repeatedly switches on and off without pulling the spray gun trigger. Possible Cause The power supply cord is not connected to an electrical outlet. The GFCI has interrupted the electrical circuit. The electric motor is too warm. The mains voltage is too low. The power supply cord is not connected to an electrical outlet. The GFCI has interrupted the electrical circuit. The electric motor is too warm. There is a leak in the high-pressure pump, high-pressure hose or spray attachment. Remedy ► Connect the power supply cord to a properly installed electrical outlet. ► Reset the GFCI, @ 10.2. ► Switch off other loads connected to the same circuit. ► If the pressure washer still does not start, disconnect the pressure washer from the power supply and have it inspected by an authorized STIHL servicing dealer before further use. ► Allow the pressure washer to cool at ambient temperatures for approximately 5 minutes. ► Clean the nozzle, @ 16.3. ► Pull and hold the spray gun trigger and switch on the pressure washer. ► Switch off other loads connected to the same electrical circuit. ► Connect the power supply cord to a properly installed electrical outlet. ► Reset the GFCI, @ 10.2. ► If the pressure washer still does not start, disconnect the pressure washer from the power supply and have it inspected by an authorized STIHL servicing dealer before further use. ► Allow the pressure washer to cool at ambient temperatures for approximately 5 minutes. ► Clean the nozzle, @ 16.3. ► Have the pressure washer inspected and repaired by an authorized STIHL servicing dealer. 0458-004-8621-A 33

Section	Page
1 Introduction	4
2 Guide to Using this Manual	4
2.1 Signal Words	4
2.2 Symbols in Text	5
3 Main Parts	6
3.1 Pressure Washer	6
3.2 Spray Attachment	7
4 Safety Symbols on the Product	7
4.1 Pressure Washer	7
5 IMPORTANT SAFETY INSTRUCTIONS	8
5.1 General Safety Warnings and Instructions	8
5.2 Intended Use	10
5.3 Operator	10
5.4 Personal Protective Equipment	11
5.5 Pressure Washer	11
5.6 Power Supply Cord	12
5.7 Batteries	12
5.8 Connecting the Water Supply	13
5.9 Using the Pressure Washer	14
5.9.1 Before Operation	14
5.9.2 Holding and Controlling the Pressure Washer	15
5.9.3 Working Conditions	15
5.9.4 Operating Instructions	16
6 Maintenance, Repair and Storage	18
6.1 Warnings and Instructions	18
7 Before Starting Work	19
7.1 Preparing the Pressure Washer for Operation	19
8 Assembling the Pressure Washer	19
8.1 Assembling Parts and Accessories	19
8.2 Connecting the High-Pressure Hose	20
8.3 Installing the Batteries	20
8.4 Spray Gun and Lance	21
8.4.1 Connecting the Spray Gun and Lance	21
8.4.2 Removing the Spray Gun and Lance	21
8.5 Inserting and Removing the Spray Nozzle	22
8.5.1 Inserting the 3-in-1 Nozzle	22
8.5.2 Removing the 3-in-1 Nozzle	22
9 Connecting the Water Supply	23
9.1 Connecting the Pressure Washer to the Mains Water Supply	23
10 Ground Fault Circuit Interrupter (GFCI)	24
10.1 Testing the GFCI	24
10.2 Resetting the GFCI	25
11 Switching the Pressure Washer On and Off	25
11.1 Switching On	25
11.2 Switching Off	25
12 During Operation	26
12.1 Unrolling the High-Pressure Hose	26
12.2 Activating and Locking the Spray Gun Trigger	26
12.3 Setting the Working Pressure	27
12.4 Adding Detergents	27
12.5 Cleaning	27
13 After Finishing Work	29
13.1 Preparing for Transportation or Storage	29
13.2 Protecting the Pressure Washer in Winter Conditions	29
14 Transporting	30
14.1 Transporting the Pressure Washer	30
15 Storing	31
15.1 Storing the Pressure Washer	31
16 Cleaning	31
16.1 Flush the Pressure Washer	31
16.2 Cleaning the Pressure Washer	31
16.3 Cleaning the Nozzle and Spray Lance	31
16.4 Cleaning the Water Intake Screen	32
17 Inspection and Maintenance	33
17.1 Inspection and Maintenance Chart	33
17.2 Inspecting and Maintaining the Pressure Washer	34
17.3 Lubricating the Gaskets	34
18 Troubleshooting Guide	35
18.1 Pressure Washer	35
19 Specifications	37
19.1 STIHL RE 100.0 PLUS CONTROL	37
19.2 Symbols on the Pressure Washer	37
19.3 Engineering Improvements	38
19.4 FCC 15 Information to the User	38
20 Replacement Parts and Equipment	39
20.1 Genuine STIHL Replacement Parts	39
21 Disposal	39
21.1 Battery Recycling	39
22 Limited Warranty	39
22.1 STIHL Incorporated Limited Warranty Policy	39
23 Trademarks	39
23.1 Registered Trademarks	39
23.2 Common Law Trademarks	39
24 Addresses	40
24.1 STIHL Incorporated	40
1 Introducción	42
2 Acerca de este manual de instrucciones	42
2.1 Palabras identificadoras	42
2.2 Símbolos en el texto	43
3 Componentes importantes	44
3.1 Hidrolavadora	44
3.2 Accesorio pulverizador	45
4 Símbolos de seguridad en el producto	45
4.1 Hidrolavadora	45
5 INSTRUCCIONES IMPORTANTES DE SEGURIDAD	46
5.1 Advertencias e instrucciones generales sobre seguridad	46
5.2 Uso previsto	48
5.3 Operador	49
5.4 Equipos de protección personal	49
5.5 Hidrolavadora	49
5.6 Cable eléctrico	50
5.7 Pilas	51
5.8 Conexión del suministro de agua	52
5.9 Uso de la hidrolavadora	53
5.9.1 Antes del uso	53
5.9.2 Sujeción y control de la hidrolavadora	53
5.9.3 Condiciones de trabajo	54
5.9.4 Instrucciones de manejo	55
6 Mantenimiento, reparación y almacenamiento	57
6.1 Advertencias e instrucciones	57
7 Antes de empezar a trabajar	58
7.1 Preparación de la hidrolavadora para el funcionamiento	58
8 Armado de la hidrolavadora	58
8.1 Armado de las piezas y accesorios	58
8.2 Conexión de la manguera de presión alta	59
8.3 Instalación de las pilas	59
8.4 Pistola rociadora y lanza	60
8.4.1 Conexión de la pistola rociadora y la lanza	60
8.4.2 Quitar la pistola y la lanza de rociado	61
8.5 Inserción y retiro de la boquilla	61
8.5.1 Inserción de la boquilla 3 en 1	61
8.5.2 Retiro de la boquilla 3 en 1	62
9 Conexión del suministro de agua	62
9.1 Conexión de la hidrolavadora al suministro de agua	62
10 Interruptor de circuito de descarga a tierra (GFCI)	63
10.1 Pruebe el GFCI, .	63
10.2 Reposición del GFCI	64
11 Encendido y apagado de la hidrolavadora	64
11.1 Encendido	64
11.2 Apagado	65
12 Durante el funcionamiento	65
12.1 Desenrollado de la manguera de presión alta	65
12.2 Activación y bloqueo del gatillo de la pistola rociadora	65
12.3 Fijación de la presión de trabajo	66
12.4 Adición de detergentes	67
12.5 Limpieza	67
13 Después de completar el trabajo	68
13.1 Preparación para el transporte o el almacenamiento	68
13.2 Protección de la hidrolavadora en condiciones de invierno	69
14 Transporte	70
14.1 Transporte de la hidrolavadora	70
15 Almacenamiento	70
15.1 Almacenamiento de la hidrolavadora	70
16 Limpieza	71
16.1 Enjuague de la hidrolavadora	71
16.2 Limpieza de la hidrolavadora	71
16.3 Limpieza de la boquilla y de la lanza de pulverización	71
16.4 Limpieza de la malla de admisión de agua	72
17 Inspección y mantenimiento	73
17.1 Tabla de inspección y mantenimiento	73
17.2 Inspección y mantenimiento de la hidrolavadora	74
17.3 Lubricación de las juntas	74
18 Guía de solución de problemas	75
18.1 Hidrolavadora	75
19 Especificaciones	77
19.1 STIHL RE 100.0 PLUS CONTROL	77
19.2 Símbolos en la hidrolavadora	77
19.3 Mejoramientos técnicos	78
19.4 Información de la parte 15 de FCC para el usuario	78
20 Piezas y equipos de repuesto	79
20.1 Piezas de repuesto originales de STIHL	79
21 Eliminación	79
21.1 Reciclado de las pilas	79
22 Garantía limitada	79
22.1 Política de garantía limitada de STIHL Incorporated	79
23 Marcas comerciales	79
23.1 Marcas comerciales registradas	79
23.2 Marcas comerciales por ley común	79
24 Direcciones	80

Match case Limit results 1 per page

0458-004-8621-A

English

18 Troubleshooting Guide

18.1

Pressure Washer

Troubleshooting Guide

Before troubleshooting, switch off the pressure washer and disconnect the unit from the power supply. Relieve all system

pressure by pulling the trigger switch. Lock the spray gun trigger.

Condition

Possible Cause

Remedy

The pressure washer does

not start although the spray

gun trigger is pulled.

The power supply cord is not connected

to an electrical outlet.

►

Connect the power supply cord to a properly

installed electrical outlet.

The GFCI has interrupted the electrical

circuit.

►

Reset the GFCI,

10.2.

►

Switch off other loads connected to the same

circuit.

►

If the pressure washer still does not start,

disconnect the pressure washer from the power

supply and have it inspected by an authorized

STIHL servicing dealer before further use.

The electric motor is too warm.

►

Allow the pressure washer to cool at ambient

temperatures for approximately 5 minutes.

►

Clean the nozzle,

16.3.

The pressure washer does

not start when switched on.

The electric motor hums.

The mains voltage is too low.

►

Pull and hold the spray gun trigger and switch on

the pressure washer.

►

Switch off other loads connected to the same

electrical circuit.

The pressure washer

switches off while in

operation.

The power supply cord is not connected

to an electrical outlet.

►

Connect the power supply cord to a properly

installed electrical outlet.

The GFCI has interrupted the electrical

circuit.

►

Reset the GFCI,

10.2.

►

If the pressure washer still does not start,

disconnect the pressure washer from the power

supply and have it inspected by an authorized

STIHL servicing dealer before further use.

The electric motor is too warm.

►

Allow the pressure washer to cool at ambient

temperatures for approximately 5 minutes.

►

Clean the nozzle,

16.3.

The high-pressure pump

repeatedly switches on and

off without pulling the spray

gun trigger.

There is a leak in the high-pressure

pump, high-pressure hose or spray

attachment.

►

Have the pressure washer inspected and

repaired by an authorized STIHL servicing

dealer.