Stihl FC 110 Product Instruction Manual - Page 16

Mounting the Loop Handle, Adjusting the Throttle, Cable

Get Stihl FC 110 PDF manuals and user guides View all Stihl FC 110 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Mounting the Loop Handle 1 English / USA Adjusting the Throttle Cable* A properly adjusted throttle cable is the precondition for correct operation in the full throttle, starting throttle and idle positions. Adjust the throttle cable only after the unit is fully assembled. 355BA030 KN 343BA023 KN 002BA163 KN 2 4 3 A : Fit the loop handle (1) on the drive tube 8" / 20 cm (A) forward of the control handle (2). : Position the clamp (3) against the drive tube and slide it into the loop handle. 5 50 mm ( 2" ) : Fit square nut (4) in the loop handle, insert the clamp screw (5) from the other side and tighten down securely. Adjusting loop handle to most comfortable position: : Release clamp screw (5). : Move the loop handle along the drive tube as required - retighten the clamp screw. : Use a suitable tool to push the slide to the bottom of the slot (see illustration). FC 110 * see "Guide to Using this Manual" 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
15
FC 110
English / USA
:
Fit the loop handle
(1)
on the drive
tube 8" / 20 cm
(A)
forward of the
control handle
(2).
:
Position the clamp
(3)
against the
drive tube and slide it into the loop
handle.
:
Fit square nut
(4)
in the loop handle,
insert the clamp screw
(5)
from the
other side and tighten down
securely.
Adjusting loop handle to most
comfortable position:
:
Release clamp screw
(5)
.
:
Move the loop handle along the
drive tube as required - retighten the
clamp screw.
A properly adjusted throttle cable is
the precondition for correct
operation in the full throttle, starting
throttle and idle positions.
Adjust the throttle cable only after
the unit is fully assembled.
:
Use a suitable tool to push the slide
to the bottom of the slot (see
illustration).
*
see "Guide to Using this Manual"
Mounting the Loop Handle
3
355BA030 KN
1
2
A
343BA023 KN
5
4
50 mm
( 2" )
Adjusting the Throttle
Cable*
002BA163 KN