Sony CDX-GT55UIW Installation/Connections - Page 2
Toyota, Nissan
View all Sony CDX-GT55UIW manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 2 highlights
1 2 Face the hook inwards. El gancho debe encontrarse en la parte interior. 1 2 Claws Uñas 3 Dashboard Tablero A TOYOTA size 5 × max. 8 mm (7/32 × max. 5/16 in) Tamaño 5 × 8 mm máx. to dashboard/center console al tablero o consola central B NISSAN size 5 × max. 8 mm (7/32 × max. 5/16 in) Tamaño 5 × 8 mm máx. to dashboard/center console al tablero o consola central Bracket Soporte Bracket Soporte Existing parts supplied with your car Piezas existentes suministradas con su automóvil size 5 × max. 8 mm (7/32 × max. 5/16 in) Tamaño 5 × 8 mm máx. Bracket Soporte Bracket Soporte Existing parts supplied with your car Piezas existentes suministradas con su automóvil size 5 × max. 8 mm (7/32 × max. 5/16 in) Tamaño 5 × 8 mm máx. A B Precautions Choose the installation location carefully so that the unit will not interfere with normal driving operations. Avoid installing the unit in areas subject to dust, dirt, excessive vibration, or high temperatures, such as in direct sunlight or near heater ducts. Use only the supplied mounting hardware for a safe and secure installation. Mounting angle adjustment Adjust the mounting angle to less than 45°. Removing the protection collar and the bracket Before installing the unit, remove the protection collar and the bracket from the unit. 1 Remove the protection collar . Pinch both edges of the protection collar , then pull it out. 2 Remove the bracket . Insert both release keys together between the unit and the bracket until they click. Pull down the bracket , then pull up the unit to separate. Mounting example Installation in the dashboard Notes Bend these claws outward for a tight fit, if necessary (-2). Make sure that the 4 catches on the protection collar are properly engaged in the slots of the unit (-3). How to detach and attach the front panel Before installing the unit, detach the front panel. -A To detach Before detaching the front panel, be sure to press and hold Press , and pull it off towards you. -B To attach Engage part of the front panel with part of the unit, as illustrated, and push the left side into position until it clicks. Warning if your car's ignition has no ACC position Be sure to set the Auto Off function. For details, see the supplied Operating Instructions. The unit will shut off completely and automatically in the set time after the unit is turned off, which prevents battery drain. If you do not set the Auto Off function, press and hold until the display disappears each time you turn the ignition off. RESET button When the installation and connections are completed, be sure to press the RESET button with a ball-point pen, etc., after detaching the front panel. Mounting the unit in a Japanese car You may not be able to install this unit in some makes of Japanese cars. In such a case, consult your Sony dealer. Note To prevent malfunction, install only with the supplied screws . Precauciones Elija cuidadosamente el lugar de montaje de forma que la unidad no interfiera con las funciones normales de conducción. Evite instalar la unidad donde pueda quedar sometida a polvo, suciedad, vibraciones excesivas o altas temperaturas, por ejemplo, a la luz solar directa o cerca de conductos de calefacción. Para realizar una instalación segura y firme, utilice solamente elementos de instalación suministrados. Ajuste del ángulo de montaje Ajuste el ángulo de montaje a menos de 45°. Extracción del marco de protección y del soporte Antes de instalar la unidad, retire el marco de protección y el soporte de la misma. 1 Retire el marco de protección . Apriete ambos bordes del marco de protección y, a continuación, tire de él hacia fuera. 2 Retire el soporte . Inserte ambas llaves de liberación entre la unidad y el soporte hasta que encajen. Presione el soporte y, a continuación, levante la unidad para separar ambos elementos. Ejemplo de montaje Instalación en el tablero Notas Si es necesario, doble las uñas hacia fuera para que encaje firmemente (-2). Compruebe que los 4 enganches del marco de protección estén bien fijados en las ranuras de la unidad (-3). Forma de extraer e instalar el panel frontal Antes de instalar la unidad, extraiga el panel frontal. -A Para extraerlo Antes de extraer el panel frontal, asegúrese de mantener presionado Presione y luego extráigalo hacia usted. -B Para instalarlo Coloque la parte del panel frontal en la parte de la unidad, como se muestra en la ilustración, y después presione la parte izquierda hasta que encaje. Advertencia: si el encendido del automóvil no dispone de una posición ACC Asegúrese de ajustar la función de desconexión automática. Para obtener más información, consulte el manual de instrucciones suministrado. La unidad se apagará completa y automáticamente en el tiempo establecido después de que se desconecte la unidad, lo que evita que se desgaste la batería. Si no ha ajustado la función de desconexión automática, mantenga presionado cada vez que apague el interruptor de encendido, hasta que la pantalla desaparezca. Botón RESET Una vez finalizada la instalación y las conexiones, desmonte el panel frontal y presione el botón RESET con un bolígrafo o un objeto similar. Montaje de la unidad en un automóvil japonés Es posible que no pueda instalar esta unidad en algunos automóviles japoneses. En tal caso, consulte a su distribuidor Sony. Nota Para evitar que se produzcan fallas de funcionamiento, realice la instalación solamente con los tornillos suministrados .