Sharp PG-D3010X PG-D2710X PG-D3010X PG-D3510X Operation Manual - Page 58

Setting Up the Projector Network Environment (“Network” Menu), Setting a Password

Get Sharp PG-D3010X PDF manuals and user guides
UPC - 074000365872
View all Sharp PG-D3010X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

Setting Up the Projector Network Environment ("Network" Menu) Menu operation n Page 40 Pict. SIG SCR PRJ1 PRJ2 Network 1 Password Disable 2 DHCP Client Off 3 TCP/IP 4 Reset Network Setting 5 Restart Network IP Address X X X . X X X . X X X . X X X MAC Address X X : X X : X X : X X : X X : X X 6 Projector XX-XXXX Link Disconnected SEL./ADJ. ENTER END 1 Setting a Password If you do not want others to change the setting for the "Network" menu, set a password. aSetting a Password 1 Select "Password", then press ENTER or Q. • The screen for entering the password appears. Setting the Password Network Old Password New Password Reconfirm 2 Press P or R to set the first digit in "New Password", then press Q. 3 Enter the remaining 3 digits, then press ENTER. • To return to the previous digit, press O. 4 Enter the same password in "Reconfirm", then press ENTER. • The status for "Password" changes to "Enable". Note • Once the password is set, you must enter the password to change the "Network" menu settings. a Changing the Password 1 54 Select "Password", then press ENTER or Q. • The screen for entering the password appears. 2 Enter the password in "Old Password" using P, R, Q and O, then press ENTER. 3 Enter the password in "New Password" using P, R, Q and O, then press ENTER. 4 Enter the same password again in "Reconfirm" using P, R, Q and O, then press ENTER. Note • If you do not need the password protection for the "Network" menu settings anymore, press ENTER without entering the new password in steps 3 and 4. • To cancel the password settings, press RETURN. If you forget the password If you forget the password, perform the following procedure to delete it, then set a new password. On the projector, press ɹ. Note • If ENTER is held down for more than 5 seconds, the operation buttons on the projector will be locked. (See page 52.) • You cannot use the buttons on the remote control to delete the password.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
54
Setting Up the Projector Network Environment (“Network” Menu)
Menu operation
n
Page
40
SCR
SIG
PRJ1
PRJ2
SEL./ADJ.
ENTER
END
Pict.
Network
Password
Disable
DHCP Client
Off
Restart Network
Reset Network Setting
TCP/IP
IP Address
XXX.XXX.XXX.XXX
MAC Address
XX : XX : XX : XX : XX : XX
Projector
XX-XXXX
Link
±
Disconnected
6
4
2
3
1
5
1
Setting a Password
If you do not want others to change the setting
for the “Network” menu, set a password.
a
Setting a Password
1
Select “Password”, then press
ENTER
or
Q
.
The screen for entering the password
appears.
Setting the Password
Old Password
New Password
Reconfirm
–
–––
–
–––
––––
Network
2
Press
P
or
R
to set the first digit
in “New Password”, then press
Q
.
3
Enter the remaining 3 digits, then
press
ENTER
.
To return to the previous digit, press
O
.
4
Enter the same password in
“Reconfirm”, then press
ENTER
.
The status for “Password” changes to
“Enable”.
Once the password is set, you must enter the
password to change the “Network” menu
settings.
•
Note
a
Changing the Password
1
Select “Password”, then press
ENTER
or
Q
.
The screen for entering the password
appears.
•
•
•
•
1
2
3
4
1
2
Enter the password in “Old
Password” using
P
,
R
,
Q
and
O
,
then press
ENTER
.
3
Enter the password in “New
Password” using
P
,
R
,
Q
and
O
,
then press
ENTER
.
4
Enter the same password again
in “Reconfirm” using
P
,
R
,
Q
and
O
, then press
ENTER
.
If you do not need the password protection
for the “Network” menu settings anymore,
press
ENTER
without entering the new
password in steps 3 and 4.
To cancel the password settings, press
RETURN
.
•
•
Note
If you forget the password
If you forget the password, perform the
following procedure to delete it, then set a
new password.
On the projector, press
.
If
ENTER
is held down for more than 5
seconds, the operation buttons on the
projector will be locked. (See page
52
.)
You cannot use the buttons on the
remote control to delete the password.
•
•
Note
2
3
4