Samsung WA55CG7100AVUS User Manual - Page 27

STEP 5, Power on, Run a test cycle

Get Samsung WA55CG7100AVUS PDF manuals and user guides View all Samsung WA55CG7100AVUS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

STEP 5 Power on Plug the power cord into an AC 120 V / 60 Hz / 15 AMP approved electrical outlet protected by a 15-amp fuse or circuit breaker. Then, press Power to turn on the washer. STEP 6 Run a test cycle Run a test cycle as follows to check if your washer is properly installed. 1. Load about 6 lb. of laundry into the tub. 2. Press Power to turn on your washer. 3. Turn the Cycle Selector to RINSE+SPIN. 4. Press and hold Start/Pause (Hold to Start) to start the test cycle. 5. The washer should not rock or vibrate excessively when water is supplied or when washing and spinning, and should drain well during the spin cycle. NOTE • If water leaks while water is being supplied or drained, check the water connections. See "Connect the water hose" on page 21. • If the washer rocks and vibrates excessively, level your washer again. See "Level the washer" on page 24. Untitled-1 27 English 27 2023-09-11 7:09:40

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
English
27
STEP 5
Power on
Plug the power cord into an AC 120 V / 60 Hz / 15 AMP approved electrical outlet protected by a 15-amp fuse
or circuit breaker. Then, press
Power
to turn on the washer.
STEP 6
Run a test cycle
Run a test cycle as follows to check if your washer is properly installed.
1.
Load about 6 lb. of laundry into the tub.
2.
Press
Power
to turn on your washer.
3.
Turn the
Cycle Selector
to
RINSE+SPIN
.
4.
Press and hold
Start/Pause (Hold to Start)
to start the test cycle.
5.
The washer should not rock or vibrate excessively when water is supplied or when washing and spinning,
and should drain well during the spin cycle.
NOTE
•
If water leaks while water is being supplied or drained, check the water connections. See “
Connect the
water hose
” on page
21
.
•
If the washer rocks and vibrates excessively, level your washer again. See “
Level the washer
” on page
24
.
Untitled-1
27
2023-09-11
°° 7:09:40