Rocketfish RF-WHP02 User Manual (English) - Page 24

Specifications - rf whp01 wireless headphones

Page 24 highlights

08-1077 RF-WHP01-WHP02.book Page 24 Thursday, March 27, 2008 1:29 PM Problem Solution Sound interference • Move the docking station slowly to find the best reception position for your headphones. • Shorten the distance between your headphones and the docking station. The maximum distance is 98 feet (WHP02) or 65 feet (WHP01). • Check if there are any obvious radio frequency interference sources near your system. No communication • Make sure that the AC adapter is connected to the docking station. between the • Check if the two supplied batteries are installed into the headphone battery headphones and compartments. docking station • Check if one or both batteries are exhausted. WHP02: The headphones and docking station power indicators light up after the headphone switch is set to ON and AUX IN/MIC IN is set on the docking system. WHP01: The headphones and docking station power indicators light up after the headphone switch is set to ON and the /| button on the docking system is pressed. • If they are lit green solidly, then a communication link has been successfully established between the system. • If they are blinking green on one, or both units, then press and hold the CONNECT button on the headphones and docking station for three seconds consecutively. (The headphones' CONNECT button is on the left earpiece and the docking station's CONNECT button is on its back.) This puts the system into the "connection mode" for about 30 seconds. The system proceeds with the connection process between the headphones and docking station. While in "connection mode", the LED indicators of headphones and docking station blink between red and green alternatively. When an active link is established between the headphones and docking station, the LED indicators are solid on and will not blink. Note: Try pressing the CONNECT button again if the LED indicators keep blinking after 30 seconds. Specifications Speaker 40 mm Ferrite Impedance 32 ohm Headphone type Circumaural Headband Auto Adjusting Headband Wireless type 2.4 Ghz ISM band Distance 98 feet (30 m) line-of-sight (WHP02) 65 feet (20 m) line-of-sight (WHP01) Speaker input power 10 mW / 30 mW 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92

24
Specifications
Sound interference
Move the docking station slowly to find the best reception position for your
headphones.
Shorten the distance between your headphones and the docking station.
The maximum distance is 98 feet (WHP02) or 65 feet (WHP01).
Check if there are any obvious radio frequency interference sources near
your system.
No communication
between the
headphones and
docking station
Make sure that the AC adapter is connected to the docking station.
Check if the two supplied batteries are installed into the headphone battery
compartments.
Check if one or both batteries are exhausted.
WHP02:
The headphones and docking station power indicators light up after the
headphone switch is set to
ON
and
AUX IN/MIC IN
is set on the docking system.
WHP01:
The headphones and docking station power indicators light up after the
headphone switch is set to
ON
and the
/
|
button on the docking system is
pressed.
If they are lit green solidly, then a communication link has been successfully
established between the system.
If they are blinking green on one, or both units, then press and hold the
CONNECT
button on the headphones and docking station for three seconds
consecutively. (The headphones’
CONNECT
button is on the left earpiece
and the docking station’s
CONNECT
button is on its back.) This puts the
system into the “connection mode” for about 30 seconds. The system
proceeds with the connection process between the headphones and
docking station. While in “connection mode”, the LED indicators of
headphones and docking station blink between red and green alternatively.
When an active link is established between the headphones and docking
station, the LED indicators are solid on and will not blink.
Note:
Try pressing the
CONNECT
button again if the LED indicators keep blinking
after 30 seconds.
Speaker
40 mm Ferrite
Impedance
32 ohm
Headphone type
Circumaural
Headband
Auto Adjusting Headband
Wireless type
2.4 Ghz ISM band
Distance
98 feet (30 m) line-of-sight (WHP02)
65 feet (20 m) line-of-sight (WHP01)
Speaker input power
10 mW / 30 mW
Problem
Solution
08-1077 RF-WHP01-WHP02.book
Page 24
Thursday, March 27, 2008
1:29 PM