Pyle PSWRM70 PSWRM70 Manual 1 - Page 5

7.0 Regatta Timer Mode - Countdown Timer and the Quick-Set-Values the indicator flashing the time which the timer will countdown from (hour, minute and second) Current Time Regatta Timer Display 1 min [L/R] 3 min [L/R] 5 min [L/R] 10 min [L/R] [L/R] [L/R] [L/R] User Preset Value 45 min 15 min Quick-Set-Value Timer Setting Sequence Regatta Timer Display + The Watch includes a Regatta Timer Mode which measures the elapse of a fix period of time (target time). + The timer starts down-counting from the target time to zero and then it starts up-counting. + The target time can be set by using Quick Set Value or User preset Value following the adjacent diagram. + When the Regatta Timer Display is selected, the Watch will show the following items on the display: + The Target time will appear on the middle row. + The current time will appear on the bottom row. + The elapse of second will represent analogically by the bar-indicator which around the display. The Quick-Set-Value + The Quick-Set-Value is a set of values w h i c h p r e installed into the Watch. These values can NOT be changed by the user. + The Watch includes 6 Quick-Set Values, they are 1, 3, 5, 10, 15 and 45 minutes. The User Preset Value + The User Preset Value is a value which can be set by the user, and it can be set up to 99 hours 59 minutes 99 seconds. + Once the User Preset Value has been set, such as 30 minutes, it will store into the Watch for recall the next time. + To set the User Preset Value, check the coming chapter 7.1 for more detail. 7.1 Regatta Timer Mode - Setting the User Preset Value Regatta Timer Display hold [M] hold [M] digits selected (flashing) Setting Display hour [M] [M] minute Second [M] How to Set the User Preset Value + To select setting display, hold the [M] button for 2 seconds, and the flashing "SET" icon will appear. + In setting display, press the [M] button to change the selection among hour, minute and second following the adjacent diagram. + When the digits are flashing (selected), press the [S/S] or [L/R] button to increase / decrease the number. (Hold down the button to change the number at a higher speed). + When the setting is completed, hold down the [M] button to exit the setting display. The Watch will also exit the setting display if NO keystroke has been activated for 1 minute [S/S] / [L/R] hold [S/S] / hold [L/R] Increase/ decrease the number Increase/decrease the number at a higher speed User Preset Value Setting Sequence 7.2 Regatta Timer Mode - Using the Regatta Timer [S/S] digits start counting Regatta Timer Display [L/R] NOTE: This diagram exhibits the connection between different displays only, and hence the numbers showing on these display do not conform to fact for some instance. Counting Display [S/S] digits stop counting Stop Counting Display Beep Beep Beep Beep Beep Beep Beep Beep Beep Beep start 10 9 8 7 6 5 4 3 2 1 minute(s) Beep Beep Beep Beep Beep start 50 40 30 20 10 seconds Beep Beep Beep Beep Beep Beep Beep Beep Beep Beep-Beep for 30 sec. start 9 8 7 6 5 4 3 2 1 0 second(s) Regatta Timer Alarm Sounds Chronograph auto-start How to Use the Regatta Timer + When a target time is set by using the Quick Set Value or User preset Value, press the [S/S] button to start the counting. When the timer is counting, press the [S/S] button once again to stop the counting. + Once the timer is started, the countdown time will show on the display continuously, and the Watch will alert the user by beeping as follows: + The last 10 minutes: The watch will beep once for every minute. + The last one minute: The watch will beep for every 10 seconds. + The last 10 seconds: The watch will beep for every second(s). + At zero: the Watch will switch to Chronograph Mode and start up-counting automatically, and it will beep for 30 seconds. How to Reload the Timer + To reload the timer with the current target time for a new counting before the Watch counts to zero, press the [L/R] button once when the timer was stopped. + To start a new counting from a new target time, set the timer again. 8.0 Dual Time Mode - Dual Time and Setting the Dual Time digits selected (flashing) Dual Time Display hold [M] hold [M] Setting Display [M] minute hour [S/S] / [L/R] hold [S/S] / hold [L/R] Increase/ decrease the number Increase/decrease the number at a higher speed User Preset Value Setting Sequence Dual Time Display + The Watch includes a Dual Time Mode which shows the current time for a second time zone. + The second digits of the dual time is the same as the current time. + When the Dual Time Display is selected, the Watch will show the following items on the display: + The dual time will appear on the middle row. + The elapse of second will represent analogically by the bar-indicator which around the display. To Set the Dual Time + To select setting display, hold down the [M] button for 2 seconds in Dual Time Mode, and then the flashing "SET" icon will appear. + In setting display, press the [M] button to change the selection between hour and minute. + When the digits are flashing (selected), press the [S/S] / [L/R] button to increase / decrease the number. (Hold down the button change the number at a higher speed). + When the setting is completed, hold down the [M] button to exit the setting display. The Watch will also exit the setting display if NO keystroke has been activated for 1 minute