Panasonic UB-T780BP Operating Instructions - Page 47

Confirming the elite Panaboard Operation, Confirming the Interactive Features - interactive panaboard

Get Panasonic UB-T780BP PDF manuals and user guides View all Panasonic UB-T780BP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Installation Manual Confirming the elite Panaboard Operation After assembling the elite Panaboard, confirm that it operates properly by following the procedure below. Action Operation Checkpoints Measure 1 Connect to a computer Green LED lights. (Normal operation) using a USB cable. Green LED does not light, or Check the USB cable. red LED is blinking. • Check if the USB cable is connected properly. • Disconnect the USB cable from the computer, and then connect it again. 1 Confirming the Interactive Features 1. Following the procedure in "Installing the elite Panaboard software" (page 17), install the software and, and connect the included USB cable. 2. Confirm that the interactive features are operating correctly. • If a projector is not available, confirm operation using only the elite Panaboard and computer. • When the elite Panaboard software starts, the calibration screen is displayed on the computer screen. • Perform tentative calibration by pressing the 5 points on the elite Panaboard with the electronic pen, as shown in the illustration below. For precise adjustment, it is necessary to use a projector. Approx. 100 mm (3 7/8 in.) Approx. 1 2 100 mm (3 7/8 in.) 5 4 3 • With the elite Panaboard software running, enter White Background mode and select the marker tool. Confirm operation by writing on the screen board with the electronic pen and checking that the writing is displayed on the computer's screen. (Your writing with the electronic pen will not appear on the screen board itself.) Operating Instructions (For Basic Operations) 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
Confirming the elite Panaboard Operation
After assembling the elite Panaboard, confirm that it operates properly by following the procedure below.
Action
Checkpoints
Operation
Measure
1
Connect to a computer
using a USB cable.
Green LED lights.
(Normal operation)
Green LED does not light, or
red LED is blinking.
Check the USB cable.
•
Check if the USB cable is connected
properly.
•
Disconnect the USB cable from the
computer, and then connect it again.
Confirming the Interactive Features
1.
Following the procedure in "Installing the elite Panaboard software" (page 17), install the software
and, and connect the included USB cable.
2.
Confirm that the interactive features are operating correctly.
•
If a projector is not available, confirm operation using only the elite Panaboard and computer.
•
When the elite Panaboard software starts, the calibration screen is displayed on the computer screen.
•
Perform tentative calibration by pressing the 5 points on the elite Panaboard with the electronic pen,
as shown in the illustration below.
For precise adjustment, it is necessary to use a projector.
Approx.
100 mm (3
7
/
8
in.)
Approx. 100 mm (3
7
/
8
in.)
1
3
4
5
2
•
With the elite Panaboard software running, enter White Background mode and select the marker tool.
Confirm operation by writing on the screen board with the electronic pen and checking that the writing
is displayed on the computer's screen. (Your writing with the electronic pen will not appear on the
screen board itself.)
Operating Instructions (For Basic Operations)
47
1
Installation Manual