Panasonic SCHC40 SAHC40 User Guide - Page 14
Memory reset (Initialization), Input level, Display function, Hands-Free Profile HFP - phones
![]() |
UPC - 885170008397
View all Panasonic SCHC40 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 14 highlights
ENGLISH External unit (continued) Input level You can select the sound input level of the Bluetooth device. Press [PLAY MODE] repeatedly to select "LEVEL 0", "LEVEL +1" or "LEVEL +2". • Select "LEVEL 0" if the sound is distorted. Display function Press [DISPLAY, -DIMMER] repeatedly to view the information of the current connected device. BLUETOOTH Connected device name Connected profiles Hands-Free Profile (HFP) This unit works as a Bluetooth hands-free for your mobile phones. You can answer or cancel an incoming call with the remote control. To answer a call ("IN CALL" blinks) Press [ ]. "CALLING" starts blinking on the display (Talk into the unit's microphone). Press [ ] again to transfer the call to the mobile phones ("TRANSFER" blinks. You may now converse using the mobile phone). To cancel a call To adjust volume To mute the microphone Press [g, ]. Press [+, VOL , -] (Adjustable from "TEL VOL 1" to "TEL VOL 10"). Press [MUTE]. Press again to cancel. (During "MIC MUTE", the caller is not able to hear your voice). • This unit does not work with Headset Profile (HSP). • When the mobile phone is too close to the microphone of this unit, noise may occur. Always keep the mobile phone away from the microphone of this unit when making a call. Disconnecting a Bluetooth device Press [ MENU] to display "DISCONNECT?" and then press [OK]. A confirmation message is displayed. Press [e,r] to select "YES" or "NO" and then press [OK]. • The connection can also be stopped when you disable Bluetooth transmission on the connected Bluetooth device. Advanced functions g To register more devices Press [ MENU]. Press [e,r] to select "NEW DEV" and then press [OK]. The unit enters pairing mode and "PAIRING" starts blinking on the display. While this unit is in pairing mode, access the Bluetooth menu of the Bluetooth device and execute a Bluetooth search to find this unit (SC-HC40). • If prompted for the passkey, enter "0000". g To select communication quality Press [ MENU]. Press [e,r] to select "LINK MODE" and then press [OK]. Press [e,r] to select the following modes and then press [OK]. • "MODE 1": Connection with emphasis on communication stability • "MODE 2": Connection with high bit rate for good audio quality (Communication might easily be disconnected in this mode, select "MODE 1" if this occurs). g To select Auto Link mode Press [ MENU]. Press [e,r] to select "AUTO LINK" and then press [OK]. Press [e,r] to select the following modes and then press [OK]. • "ON": Automatically linked even in other than Bluetooth selector • "OFF": Linked only in Bluetooth selector • These functions are unavailable if a device is connected. Disconnect the Bluetooth devices to display these functions. • When "LINKING" is displayed, pressing [ MENU] is invalid. • Auto Link works only if your device support A2DP. Changing the main unit and remote control mode The remote control and main unit are factory-set to "REMOTE 1" mode. If you find the remote control unintentionally also controls other equipment, you can switch to operate in "REMOTE 2" mode. To switch to "REMOTE 2" mode (by main unit only) Press [FM/AM/AUX] to select ''AUX''. Press and hold [FM/AM/AUX] and then press [2] until "REMOTE 2" is displayed. Press and hold [OK] and [2] for at least 2 seconds. To return to "REMOTE 1" mode Repeat the steps above but replace [2] with [1]. ("REMOTE 1" will be displayed.) Memory reset (Initialization) When the following situations occur, reset the memory: • There is no response when buttons are pressed. • You want to clear and reset the memory contents. To reset memory Disconnect the AC power supply cord. (Wait for at least 3 minutes before proceeding to step 2.) While pressing and holding down [8, POWER] on the main unit, reconnect the AC power supply cord. "--------" appears on the display. Release [8, POWER]. All the settings are returned to the factory preset. You will need to reset the memory items. RQTX1146 14 14
![](/manual_guide/products/panasonic-sahc40-sahc40-user-guide-8c19234/14.png)