Panasonic PT-EW650 Operating Instructions - Page 29

Preparing the remote control, Inserting and removing the batteries

Get Panasonic PT-EW650 PDF manuals and user guides View all Panasonic PT-EW650 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Chapter 1 Preparation - Preparing the remote control Preparing the remote control Inserting and removing the batteries ii) i) Fig. 1 Fig. 2 1) Open the cover. (Fig. 1) 2) Insert the batteries and close the cover (insert the m side first). (Fig. 2) ff When removing the batteries, perform the steps in reverse order. When using the system with multiple projectors When you use the system with multiple projectors, you can operate all the projectors simultaneously or each projector individually by using single remote control, if a unique ID number is assigned to each projector. When you want to set the ID number, at first you need to complete the Initial setting, and then after setting the ID number of the projector, set the ID number on the remote control. About Initial setting, please refer to "When the initial setting screen is displayed" (x page 47). The factory default ID number of the unit (the projector and the remote control) is set to [ALL], you can control with this setting. If necessary, please set the ID number to the remote control and the projector. About how to set the ID number of the remote control, please refer to "Setting the ID number of the remote control" (x page 59). Note ff Set the ID number of the projector from the [PROJECTOR SETUP] menu → [PROJECTOR ID] (x page 92). Connecting the remote control to the projector with a cable When you use the system with multiple projectors, use commercially available M3 stereo mini jack cables and connect the other devices to the terminal of the projector. The remote control is effective even in places where an obstacle stands in the light path or where devices are susceptible to outside light. Remote control M3 stereo mini plug cable (commercially available) Connecting to the remote control wired terminal Connecting terminals Attention ff Use a cable that is 15 m (49'3") or shorter, with 2 core shielded. The remote control may not operate when the length of the cable exceeds 15 m (49'3") or when the shielding of the cable is inadequate. ENGLISH - 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
Chapter 1
Preparation — Preparing the remote control
ENGLISH - 29
Preparing the remote control
Inserting and removing the batteries
ii)
i)
Fig. 1
Fig. 2
1)
Open the cover. (Fig. 1)
2)
Insert the batteries and close the cover (insert the
m
side first). (Fig. 2)
f
When removing the batteries, perform the steps in reverse order.
When using the system with multiple projectors
When you use the system with multiple projectors, you can operate all the projectors simultaneously or each
projector individually by using single remote control, if a unique ID number is assigned to each projector.
When you want to set the ID number, at first you need to complete the Initial setting, and then after setting the ID
number of the projector, set the ID number on the remote control.
About Initial setting, please refer to “When the initial setting screen is displayed” (
x
page 47).
The factory default ID number of the unit (the projector and the remote control) is set to [ALL], you can control with
this setting. If necessary, please set the ID number to the remote control and the projector.
About how to set the ID number of the remote control, please refer to “Setting the ID number of the remote control”
(
x
page 59).
Note
f
Set the ID number of the projector from the [PROJECTOR SETUP] menu → [PROJECTOR ID] (
x
page 92).
Connecting the remote control to the projector with a cable
When you use the system with multiple projectors, use commercially available M3 stereo mini jack cables and
connect the other devices to the <REMOTE 2 IN> terminal of the projector.
The remote control is effective even in places where an obstacle stands in the light path or where devices are
susceptible to outside light.
Remote control
M3 stereo mini plug cable (commercially available)
Connecting to the remote control wired terminal
Connecting terminals
Attention
f
Use a cable that is 15 m (49'3") or shorter, with 2 core shielded. The remote control may not operate when the length of the cable exceeds
15 m (49'3") or when the shielding of the cable is inadequate.