Panasonic ER-GP21 Operating Instructions - Page 9

Charging the clipper, Using the clipper

Get Panasonic ER-GP21 PDF manuals and user guides View all Panasonic ER-GP21 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

English Charging the clipper • Make sure that the clipper is turned off. 1 Place the clipper on the AC adaptor. 2 2 1 Insert the power plug into a household outlet. ••Charging is completed after approx. 15 hours. ••Check the charge indicator lamp ( ) glows. 3 Disconnect the power plug after charging is completed. (for safety and to reduce energy usage) ••The charge indicator lamp ( ) continues to glow after charging is complete. There is no indication to show that "charging is complete". Notes • If there is crackling noise on radios or other devices while charging, charge the clipper using a different household outlet. • When the appliance is not used for 6 months or more, the battery will weaken (leak battery fluid, etc.). Fully charge the battery once every 6 months. • When charging the clipper for the first time or when it has not been in use for more than 6 months, the lamp on the main body may not glow for a few minutes, or the operating time may shorten. Please charge it for more than 23 hours in such cases. • Recommended ambient temperature for charging is 0 °C - 35 °C (32 °F - 95 °F). Battery performance may decrease outside of the recommended temperature. • 1 full charge will provide approximately 60 minutes of continuous operation. • You can charge the battery before it is completely discharged. However, it is recommended to charge when the battery is completely discharged. The battery life depends strongly on factors such as how it is used and stored. Using the clipper • Make sure that the clipper is turned off. • The appliance may not operate in an ambient temperature approximately 0 °C (32 °F) or lower. 1 Select the trimming heights indicated on the insides and sides of the attachments. 2 Slide the power switch on the main body to the " " position to turn on the clipper. Removing and mounting the comb attachments Mounting the attachment (Example: in the case of 3 mm (1/8˝)) Slide the attachment until it clicks. click 3mm Removing the attachment Remove the attachment by pressing with your thumb. 9 ER-GP21_US.indb 9 2016/03/17 16:09:07

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
9
English
Charging the clipper
•
Make sure that the clipper is turned off.
1
1
Place the clipper on the AC
adaptor.
2
2
Insert the power plug into a
household outlet.
•
Charging is completed after approx.
15 hours.
•
Check the charge indicator lamp
(
) glows.
2
1
3
3
Disconnect the power plug after charging is
completed.
(for safety and to reduce energy usage)
•
The charge indicator lamp (
) continues to glow after
charging is complete. There is no indication to show that
“charging is complete”.
Notes
•
If there is crackling noise on radios or other devices while
charging, charge the clipper using a different household outlet.
•
When the appliance is not used for 6 months or more, the battery
will weaken (leak battery fluid, etc.). Fully charge the battery
once every 6 months.
•
When charging the clipper for the first time or when it has not
been in use for more than 6 months, the lamp on the main body
may not glow for a few minutes, or the operating time may
shorten. Please charge it for more than 23 hours in such cases.
•
Recommended ambient temperature for charging is 0 °C – 35 °C
(32 °F – 95 °F). Battery performance may decrease outside of
the recommended temperature.
•
1 full charge will provide approximately 60 minutes of continuous
operation.
•
You can charge the battery before it is completely discharged.
However, it is recommended to charge when the battery is
completely discharged. The battery life depends strongly on
factors such as how it is used and stored.
Using the clipper
•
Make sure that the clipper is turned off.
•
The appliance may not operate in an ambient temperature
approximately 0 °C (32 °F) or lower.
1
1
Select the trimming heights indicated on the
insides and sides of the attachments.
2
2
Slide the power switch on the main body to the
“
” position to turn on the clipper.
Removing and mounting the comb attachments
Mounting the attachment
(Example: in the case of 3 mm
(1/8˝))
Slide the attachment until it
clicks.
Removing the attachment
Remove the attachment by pressing
with your thumb.
3mm
click
ER-GP21_US.indb
9
2016/03/17
16:09:07