Oregon Scientific WMR100N User Manual - Page 6

Alternative Set Up, Remote Wind, Sensor On Existing Pole

Get Oregon Scientific WMR100N PDF manuals and user guides View all Oregon Scientific WMR100N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

EN 3. Insert the versatile plastic base into the pole. Align the holes of the pole with the holes of the plastic base. 4. Secure the plastic base by inserting the screw and screwing it tightly into the holes of the plastic base and pole. IMPORTANT The sensor should be positioned in an open area away from trees or other obstructions. 5. Hammer pole (cone end down) into the ground at the desired spot until versatile plastic base is level with the ground. TIP Place a block of wood between the pole and the hammer to prevent damage to the pole. 6 8 7 9 6. Assemble middle pole on top of the bottom one. 7. Using two screws, fix it firmly into place. 8. Assemble top pole on top of the middle one. 9. Using two screws, fix it firmly into place. 11 10 To mount the wind sensor: 13 14 13. Insert the wind vane into the attachment bracket. 14. Screw aluminium pole firmly into place. IMPORTANT For best results, point the wind vane North. Securing the assembled remote unit: 15 16 15. Insert the 2 rectangular base legs through the holes of the versatile base and hammer down. 16. Using the string, tie a knot on the eye pins. Hammer each eye pin into the ground at a 90° angle. IMPORTANT Using the fasteners, tighten the string. To tighten, pull fastener down. To loosen, thread the string up through the fastener eyelets. 10. Slide the vertical attachment bracket on top of the top pole. 11. Using two screws, fix it firmly into place. To mount the temperature / humidity sensor: 12 ALTERNATIVE SET UP: REMOTE WIND SENSOR ON EXISTING POLE 3 1 2 12. Slide outdoor sensor onto vertical attachment bracket. 1. Secure the plastic base onto existing pole with Ubolts, washers and bolts. 2. Insert the horizontal attachment bracket into the base. 3. Using a screw, fix firmly into place. 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
6
EN
3.
Insert the versatile plastic base into the pole.
Align the
holes of the pole with the holes of the plastic base.
4. Secure the plastic base by inserting the screw and
screwing it tightly into the holes of the plastic base
and pole.
IMPORTANT
The
sensor should be
positioned in an open
area away from trees or
other obstructions.
5.
Hammer pole (cone end down) into the ground at the
desired spot until versatile plastic base is level with
the ground.
TIP
Place a block of wood between the pole and the
hammer to prevent damage to the pole.
6
7
8
9
6.
Assemble middle pole on top of the bottom one.
7.
Using two screws, fix it firmly into place.
8.
Assemble top pole on top of the middle one.
9.
Using two screws, fix it firmly into place.
11
10
10. Slide the vertical attachment bracket on top of the top
pole.
11. Using two screws, fix it firmly into place.
To mount the temperature / humidity sensor:
12
12. Slide outdoor sensor onto vertical attachment
bracket.
To mount the wind sensor:
13
14
13. Insert the wind vane into the attachment bracket.
14. Screw aluminium pole firmly into place.
IMPORTANT
For best results, point the wind vane North.
Securing the assembled remote unit:
16
15
15. Insert the 2 rectangular base legs through the holes
of the versatile base and hammer down.
16. Using the string, tie a knot on the eye pins.
Hammer
each eye pin into the ground at a 90° angle.
IMPORTANT
Using
the fasteners, tighten
the string.
To tighten,
pull fastener down.
To loosen, thread the
string up through the
fastener eyelets.
ALTERNATIVE SET UP:
REMOTE WIND
SENSOR ON EXISTING POLE
1
2
3
1. Secure the plastic base onto existing pole with U-
bolts, washers and bolts.
2. Insert the horizontal attachment bracket into the
base.
3.
Using a screw, fix firmly into place.