Marantz SR9200 User Guide - Page 43

OTHER FUNCTION TV AUTO ON/OFF FUNCTION This function allows the component connected to the TV-VIDEO in jack to control the power (ON/OFF) to the SR9200. AUTO POWER ON 1. Be sure TV auto mode is ENABLE. (Refer page 30 : System Setup) 2. Connect your TV TUNER (etc) to the TV-VIDEO in terminal. Be sure to connect the VIDEO input. 3. Turn OFF the power to the TV TUNER and the SR9200. 4. Turn ON the TV TUNER and tune in a receivable station. 5. When the station is received, the SR9200 turns ON and TV is selected automatically. AUTO POWER OFF 1. In the above situation, turn the TV TUNER OFF or select a channel that does not contain any broadcast. 2. The power to the SR9200 switches to STANDBY after approx. 5 minutes. Notes: • AUTO POWER OFF is canceled if the SR9200 is set to a source other than TV. The function reactivates when TV is selected again. • Some TV broadcasts may cause the TV AUTO FUNCTION to turn ON. • S-Video terminal does not support "TV AUTO ON/OFF" function. ATTENUATION TO ANALOG INPUT SIGNAL VOLUME PLAY CLEAR MEMO DOWN GYRO TUNING UP F/P AUTO-TUNE T-MODE DOWN DVD DSS TV VCR 1 VCR2/DVD-R CD TAPE CD-R TUNER MULTI-SPK SLEEP S-DIRECT AUX1 MULTI ROOM A/D 7.1CH-IN AUX2 DIGITAL S-VIDEO AUX1 INPUT VIDEO L AUDIO R MUTE UP ATT If the selected analog audio input signal is greater than the capable level of internal processing, "PEAK" indicator will light up on the front display. If this happens, you should press the ATT button or tap ATT on the remote. "ATT" indicator will light up when this function is activated. The signalinput level is reduced by about the half. Attenuation will not work with the output signal of TAPE-OUT, CD-R/MD-OUT, VCR1-OUT, VCR2OUT and MULTI ROOM OUT. This function is memorized for each individual input source. LISTENING OVER HEADPHONES This jack may be used to listen to the SR9200's output through a pair of headphones. Be certain that the headphones have a standard 1/4" stereo phone plug. (Note that the main room speakers will automatically be turned off when the headphone jack is in use.) SELECT STANDBY POWER ON/STANDBY ENTER PHONES DISPLAY CLEAR MEMO DOWN GYRO TUN LD DVD DSS TV VCR 1 V MULTI-SPK SLEEP S-DIRECT AUX1 MULTI ROOM A/D 7.1CH-IN AUX2 Notes: • When using headphones, the surround mode will automatically change to STEREO. • The surround mode returns to the previous setting as soon as the plug is removed from the jack. VIDEO ON/OFF When no video signals of a DVD, etc., are connected to the SR9200 or the DVD, etc., are connected directly to a TV, the unnecessary video circuit can be turned off by selecting the "VIDEO OFF" setting. To select video off condition, tap Video off on the remote. Notes that VIDEO OFF will not work with the output signal of VCR1OUT and VCR2-OUT and MULTI ROOM OUT. DISPLAY MODE SELECTOR SELECT STANDBY POWER ON/STANDBY ENTER PHONES DISPLAY CLEAR MEMO DOWN GYRO TUNING UP F/P AUTO-TUNE T-MO LD DVD DSS TV VCR 1 VCR2/DVD-R CD TAPE CD-R MULTI-SPK SLEEP S-DIRECT AUX1 MULTI ROOM A/D 7.1CH-IN AUX2 DIGITAL S-VIDEO AUX1 INPUT VIDEO L AUDIO R You can select the display mode for the front display of the SR9200. To select this mode, press DISP button on the front panel or tap Display on the remote control unit. When this button is pressed, the display mode is switched in the following sequence. → Auto-display Off → Display Off → Normal → Auto-display Off .... In Auto display off mode, turn the display on automatically, after that any condition of SR9200 is changed. In Display off mode, turn the display off completely. Notes: • Only Disp will light up on the front display in display off condition SELECTING ANALOG AUDIO INPUT OR DIGITAL AUDIO INPUT SELECTOR SELECT STANDBY POWER ON/STANDBY ENTER PHONES DISPLAY CLEAR MEMO DOWN GYRO TUNING UP F/P AUTO-TUNE T-MO LD DVD DSS TV VCR 1 VCR2/DVD-R CD TAPE CD-R MULTI-SPK SLEEP S-DIRECT AUX1 MULTI ROOM A/D 7.1CH-IN AUX2 DIGITAL S-VIDEO AUX1 INPUT VIDEO L AUDIO R If you have already assign any digital input to input source. You can select temporarily the audio input mode for each input source with A/D button on the remote controller or front panel. When this button is pressed, the input mode is switched in the following sequence. → Digital Auto → Digital → Analog → Digital Auto.... In Digital Auto mode, the types of signals being input to the digital and analog input jacks for the selected input source are detected automatically. If no digital signal is being input, the analog input jacks are selected automatically. In Digital mode, input is fixed to an assigned digital input terminal. In analog mode, the analog input jacks are selected. This selecting is temporarily, so the result will not be stored in memory. If you need to change input mode completely, use SYSTEM SETUP in OSD menu system.(see page 28) 39 ENGLISH