Marantz PM7200 User Manual - Page 7

ENGLISH

FRAN

Ç

AIS

DEUTSCH

NEDERLANDS

ESPA

Ñ

OL

ITALIANO

PORTUGU

Ê

S

SVENSKA

DANSK

2

!3

CLASS A INDICATOR

This indicator lights when the amplifier is in the Class A operation

mode. See

“

@3

Class A Switch

”

for details.

!4

TAPE,CD-R/MD SELECTOR BUTTONS

Press one of these switches to select a connected tape deck or

CD-R/MD for monitoring or playback. Pressing a

TAPE,CD-R/MD

SELECTOR

button causes the indicator above it to light.

Pressing a

TAPE,CD-R/MD SELECTOR

button while the amplifier

is in the Standby Mode automatically turns power back on.

!5

INPUT SELECTOR

Use this selector to specify

PHONO

,

CD

,

TUNER

,

AUX 1

, or

AUX 2

as the program source for recording or play. Selecting a program

source causes the indicator above it to light.

Changing the

INPUT SELECTOR

setting while the amplifier is in

the Standby Mode automatically turns power back on.

!6

REMOTE SENSOR

The remote sensor receive infrared commands from the remote con-

trol unit. Note that the remote control unit must be pointed directly

at the remote sensor for proper operation.

!7

VOLUME CONTROL

Rotate this knob clockwise to increase volume, and counter-clock-

wise to decrease volume.

!8

MUTING INDICATOR

This indicator lights when muting is activated by pressing the remote

control unit

’

s

MUTE

button.

IMPORTANT:

Be sure to double check the

VOLUME

control setting before press

ing the remote control unit

’

s

MUTE

button to cancel muting.

Restoring audio output while the

VOLUME

control setting is too

high can damage your speakers.

!9

BALANCE CONTROL

Rotate this knob to shift the balance of stereo output left and right.

Note that turning the

BALANCE

control all the way in either direction

causes output from the other side to be eliminated entirely.

@0

RECORD (REC) SELECTOR SWITCH

Use this switch to select recording between the tape deck and CD-

R/MD or recording of the signal selected by the

INPUT SELECTOR

SWITCH

and out put from the

REC OUT

jacks.

See the note under

“

Tape Deck, CD-R/MD Operation

”

on page 4 for

full details about settings.

@1

SOURCE DIRECT SWITCH

Press this switch to turn

SOURCE DIRECT

on (depressed) and off

(raised).

When

SOURCE DIRECT

is turned on, the audio signal path is as

short and direct as possible in order to enjoy high-quality sources

under the best conditions possible.

NOTE:

Tape and CD-R/MD playback and recording are not possible when

the

SOURCE DIRECT

switch is on.

The

TONE

and

BALANCE

controls are also disabled.

Any graphic equalizer or other such

component that is connected to the

PROCESSOR IN/OUT

jacks

will not have any effect.

In order to use any of these components

or controls, it is necessary to turn the

SOURCE DIRECT

switch off.

@2

BASS AND TREBLE TONE CONTROLS

Use these controls to control the levels of their corresponding fre-

quency bands.

TREBLE

adjusts the high frequency band, while

BASS

adjusts the low frequency band. Rotating a control towards

(+) enhance the frequency band, while rotating towards (

–

)

attenuates the frequency band.

CONTROLS, CONNECTORS,

AND INDICATORS

(Figure 2)

q

REMOTE CONTROL BUS TERMINALS (REMOTE

CONT. BUS)

These terminals can used to connect other audio equipment that is

equipped with a remote control bus terminal. Connection requires a

special cable. The bus

OUT

terminal sends signal to the connected

equipment, while the bus

IN

terminals receive signals.

w

AUX1/AUX2 INPUT JACKS

These auxiliary input jacks can be used to connect the audio output

of a TV multiplex/stereo audio tuner, VCR, laserdisc system, or other

AV component audio output.

e

TUNER INPUT JACKS

Connect these jacks to the output jacks of your tuner.

r

CD INPUT JACKS

Connect these jacks to the output jacks of your compact disc player.

t

PHONO INPUT JACKS

Connect these jacks to the output jacks of your turntable. These

input jacks are exclusive for a turntable equipped with MM (Moving

Magnet) cartridge.

y

TAPE, CD-R/MD IN/OUT JACKS

Connect these jacks to the play (output) and record (input) jacks of

your recorders. Up to two decks can be connected.

u

PROCESSOR IN/OUT JACKS

Use these jacks to connect a graphic equalizer or other analog audio

processor. When not used, leave these jacks connected with the

supplied connecting pins.

i

GROUND TERMINAL

If your turntable has a grounding wire, connect it to this terminal.

o

SPEAKER SYSTEMS

Connect your speaker system(s) to these terminals. There are two

sets of terminals, so you can connect either one or two speaker

systems.

!0

AC OUTLETS (SWITCHED)

Connect the power cord of another piece of equipment (VCR, tuner,

CD) when you want the power of the connected equipment auto-

matically turned on whenever you turn on this amplifier. For this to

work correctly, the power switch of the connected equipment must

be left on. Normally, the audio output of the connected equipment

is also connected to this amplifier. Note that the total power con-

sumption of the connected all equipment must not exceed 120W.

!1

POWER CORD

Connect the power cord to a standard household power outlet.

!2

POWER SWITCH

Press this switch to turn power on (depressed) and off (raised). Note

that the power of any equipment connected to the switched AC outlet

on the rear panel (see

!0

above) is also turned on and off by operat-

ing this switch.

Turning on the power causes the

POWER

indicator to light, and the

POWER

indicator goes out when power is turned off.

While the

POWER

switch is in the ON position (depressed), you

can put use the remote control unit

’

s

SYSTEM POWER ON

and

OFF

button to switch the amplifier between standby (indicated when

the

@6

STANDBY

indicator is lit) and power on.

PM7200U(ENG)

03.12.17, 11:18 AM

Page 2

Adobe PageMaker 6.5J/PPC

Marantz PM7200 User Manual - Page 7

Controls, Connectors, And Indicators - audio amplifier

Page 7 highlights