LiftMaster 98032 LiftMaster Model 98032 Heavy Duty Shaft Collar Instruction Sh
LiftMaster 98032 Manual
View all LiftMaster 98032 manuals
Add to My Manuals
Save this manual to your list of manuals |
LiftMaster 98032 manual content summary:
- LiftMaster 98032 | LiftMaster Model 98032 Heavy Duty Shaft Collar Instruction Sh - Page 1
socket or 9/16" Open End Wrench • 6" Extender PRE-INSTALLATION 1. Close the garage door. 2. Disconnect power from the outlet. 3. Remove the lower and upper front covers Disconnect ALL electric and battery power BEFORE performing ANY service or maintenance CAUTION To prevent damage to the receiver - LiftMaster 98032 | LiftMaster Model 98032 Heavy Duty Shaft Collar Instruction Sh - Page 2
: To avoid installation difficulties, do not run the garage door garage door opener until instructed to do so. The garage door opener can be installed on either side of the door. The illustrations shown are for installation on the left side of the door. 1. Loosen the set screws on the collar. Ensure - LiftMaster 98032 | LiftMaster Model 98032 Heavy Duty Shaft Collar Instruction Sh - Page 3
refer to the accessories page of the owner's manual. 1. Close the garage door completely. 2. Slide the garage door opener onto the end of the torsion bar. /a2r turn. 9. Secure the mounting bracket to both the wall and the garage door opener. Use the provided 14-10 x 2" screws to firmly fasten the - LiftMaster 98032 | LiftMaster Model 98032 Heavy Duty Shaft Collar Instruction Sh - Page 4
4 - LiftMaster 98032 | LiftMaster Model 98032 Heavy Duty Shaft Collar Instruction Sh - Page 5
é plate 9/16 po • Rallonge de 6 pouces PRÉ-INSTALLATION 1. Fermez la porte du garage. 2. Débranchez l'alimentation de la prise. 3. Retirez le capot inférieur et le (D). 7. Retirez les deux vis 14-10 x 2 po qui maintiennent le support de montage au mur (E). 8. Retirez le bloc moteur du mur. 9. Jetez - LiftMaster 98032 | LiftMaster Model 98032 Heavy Duty Shaft Collar Instruction Sh - Page 6
collier. Arbre d'opérateur Collier Vis de rSéetgSlcargewes AffleurFlaunsht FIXEZ LES SUPPORTS DE MONTAGE SUR L'OUVRE-PORTE DE GARAGE 1. Fixez sans serrer le côté fendu du support de montage sur le même côté de l'ouvre porte de garage que le collier à l'aide de deux vis 10-32 fournies. REMARQUE - LiftMaster 98032 | LiftMaster Model 98032 Heavy Duty Shaft Collar Instruction Sh - Page 7
le collier ne touche PAS la plaque de d'appui. Si le collier de l'arbre de remplacement correspond au collier de l'arbre précédent, alignez le support de montage de l'ouvre-porte de garage sur les trous existants. Utilisez un niveau pour placer et aligner à la verticale l'ouvre-porte de - LiftMaster 98032 | LiftMaster Model 98032 Heavy Duty Shaft Collar Instruction Sh - Page 8
114-5921-000 © 2023, LiftMaster All Rights Reserved Tous droits réservés Todos los derechos reservados 8 LiftMaster 300 Windsor Drive Oak Brook, IL 60523 LiftMaster.com
1
HEAVY DUTY SHAFT COLLAR 98032
MODEL 041-0400-000
APPLICATION
This replacement kit is only intended for the heavy duty style Residential
Jackshaft Operator with 4 holes on each end of the output shaft.
NOTE:
The following images are for reference only. Your unit and shaft collar
may look different.
YOU MAY NEED:
•
3/8" 8-point socket or 3/8" Open End Wrench
•
9/16" socket or 9/16" Open End Wrench
•
6" Extender
PRE-INSTALLATION
1. Close the garage door.
2.
Disconnect power from the outlet.
3.
Remove the lower and upper front covers (A).
4.
Disconnect and remove the batteries and set aside. (B).
5. Remove wires from the
unit and label them for reinstallation. Disconnect
wires from the quick connect terminals (C).
6.
Loosen the shaft collar. First, use a 9/16 socket or open end wrench to
loosen the 4 lock nuts completely off the lock washers. Then use a 3/8"
8-point socket or open end wrench to loosen the 4 set screws on the
collar (D).
7.
Remove the two 14-10 x 2" screws holding the mounting bracket to the
wall (E).
8.
Remove the motor unit from wall.
9.
Discard the old shaft collar.
Set Screws
Collar
Operator
Shaft
E
A
B
C
D
WARNING
To prevent possible SERIOUS INJURY or DEATH:
•
Disconnect ALL electric and battery power BEFORE performing ANY
service or maintenance
CAUTION
To prevent damage to the receiver logic board, DO NOT touch printed
circuit board of replacement receiver logic board during installation.
ALWAYS wear protective gloves and eye protection when changing the
battery or working around the battery compartment.
WARNING:
This product can expose you to chemicals including
lead, which are known to the State of California to cause cancer or
birth defects or other reproductive harm. For more information go
to www.P65Warnings.ca.gov.