KitchenAid KSM70SNDXDR Owners Manual - Page 6

Using The Pouring Shield

Get KitchenAid KSM70SNDXDR PDF manuals and user guides View all KitchenAid KSM70SNDXDR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

PRODUCT ASSEMBLY 7 Lower Bowl Raise Bowl IMPORTANT: When properly adjusted, the Flat Beater will not strike on the bottom or sides of the Bowl. If the Flat Beater or the Wire Whip is so close that it strikes the bottom of the Bowl, coating may wear off the beater or wires on the whip may wear. (OPTIONAL) To adjust Beater to Bowl Cearance: Lower the Bowl to the down position. Turn the screw slightly counterclockwise (left) to raise the beater, or clockwise (right) to lower it. Adjust the beater so that it just clears the surface of the Bowl. Check again the clearance of the beater to the Bowl. USING THE POURING SHIELD* PRODUCT USAGE 1. Turn the Stand Mixer to "0" (OFF) and then Unplug. 2. Attach Bowl and Flat Beater, Dough Hook, or Wire Whip to the mixer. Attach Bowl and raise into locked position. 3. Place the shield onto the Bowl so that the Motor Head covers the U-shaped gap in the shield. This will position the pouring chute just to the right of the Attachment Hub as you face the Mixer. Press lightly so that the tabs snap the shield onto the Bowl. 4. Pour ingredients into the Bowl through the Pouring Chute. DISASSEMBLING THE PRODUCT 1. Turn the Stand Mixer to "0" (OFF) and then Unplug. 2. Lift the front of the Pouring Shield* clear of the rim of the Bowl. Pull away from the Stand Mixer. Lower the Bowl and scrape. *Available with select models only and available as an accessory purchase. 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
6
(OPTIONAL) To adjust Beater to
Bowl Cearance:
Lower the Bowl to the
down position. Turn the screw slightly
counterclockwise (left) to raise the beater,
or clockwise (right) to lower it. Adjust the
beater so that it just clears the surface of
the Bowl. Check again the clearance of
the beater to the Bowl.
7
Raise Bowl
Raise Bowl
Lower Bowl
Lower Bowl
IMPORTANT:
When properly adjusted,
the Flat Beater will not strike on the
bottom or sides of the Bowl. If the Flat
Beater or the Wire Whip is so close that
it strikes the bottom of the Bowl, coating
may wear off the beater or wires on the
whip may wear.
*Available with select models only and available as an accessory purchase.
PRODUCT USAGE
1.
Turn the Stand Mixer to “0” (OFF) and then Unplug.
2.
Attach Bowl and Flat Beater, Dough Hook, or Wire Whip to the mixer. Attach Bowl
and raise into locked position.
3.
Place the shield onto the Bowl so that the Motor Head covers the U-shaped gap in
the shield. This will position the pouring chute just to the right of the Attachment Hub
as you face the Mixer. Press lightly so that the tabs snap the shield onto the Bowl.
4.
Pour ingredients into the Bowl through the Pouring Chute.
USING THE POURING SHIELD*
DISASSEMBLING THE PRODUCT
1.
Turn the Stand Mixer to “0” (OFF) and then Unplug.
2.
Lift the front of the Pouring Shield* clear of the rim of the Bowl. Pull away from the
Stand Mixer. Lower the Bowl and scrape.
PRODUCT ASSEMBLY