Kenwood KRF-V7010 User Manual - Page 14

Preparing for surround sound 14 3 Adjust the volume levels for the speakers. Sit in your normal listening position and listen to the test tone. Adjust the volume levels for the speakers until all speakers seem to be equally loud. 1 Use the MULTI CONTROL (TUNING/SKIP) to adjust the volume when the test tone is being output from the speaker channel to be adjusted. Preparations The channel indication blinks while the test tone is being output. Lch +1 dB SP A L SW The test tone issues from the speakers for 1.5 seconds at a time in the following sequence: Lch = Cch = Rch = Sch = Lch • If you change the volume level settings for the speakers while listening to music, the settings referred to on this page are also changed. ¢ • If the speaker setting selects are changed, the speaker level settings are reset. 2 Press the SETUP key. • The receiver enters the mode for inputting the distance to the speakers. Operations 4 Input the distance to the speakers. 1 Measure the distance from the listening position to each of the speakers. Jot down the distance to each of the speakers. Distance to front speakers: ____ feets (meters) Distance to surround speakers: ____ feets (meters) 2 Use the MULTI CONTROL (TUNING/SKIP) to select the distance to the front speakers. The speaker indicator to be adjusted blinks. SP A L R 1)FT 3.)M Indication in feet Indication in meters • The allowable setting range is 1 to 30 feet (0.3 to 9.0 m), adjustable in 1 foot (0.3 m) increments. 3 Press the SETUP key. 4 Repeat steps 2 and 3 to input the distance for the surround speaker. 5 Setup is complete when the input indication reappears. CD L R SW Display when all speakers have been selected. • The speakers you selected appear on the display. Confirm that all the speakers have been correctly selected. • If you used the remote control (RC-R0507) to perform the settings, press the VIDEO key at this point to turn off the remote control's own adjustment mode. In this case, the input source is not switched. Normal playback Preparing for playback KRF-V7010/V6010/V5010 (En/T) Some preparatory steps are needed before starting playback. VIDEO 2/MONITOR ON/STANDBY AUTO POWER INPUT SELECTOR SPEAKERS A/B SPEAKERS (KRF-V5010) Turning on the receiver 1 Turn on the power to the related components. 2 Turn on the power to this receiver by pressing POWER and ON/ STANDBY keys. Selecting TAPE/MD Select the source name corresponding to the component connected to the MD/TAPE jacks. The initial factory setting is "TAPE". To change the source name associated with the MD/TAPE jacks to "MD," follow the steps below: 1 Use the INPUT SELECTOR knob to select "TAPE". 2 Hold down the AUTO key for more than two seconds. • The source indication changes to "MD". • To return to the original indication, repeat the above procedure. • You also will need to change the name input to the remote control (RC-0507) to "MD". RC3 Selecting the speaker system Press the SPEAKERS A or B key to select the speaker system to be used. A ON : Sound from the speakers connected to the SPEAKERS A terminals on the rear panel. B ON : Sound from the speakers connected to the SPEAKERS B terminals on the rear panel. A+B ON : Sound from both the speakers connected to the SPEAKERS A and B terminals on the rear panel. A+B OFF : No sound from the speakers. Use this setting when listening with headphones for stereo sound in all playback modes. • Activating a surround mode or selecting "DVD 6ch" as the input source causes speaker system A to be selected automatically. On the KRF-V5010, press the SPEAKERS key to switch the speakers on and off. The indicator for the speakers you want to use should be lit. Speaker indicator lights. SP A B L R SW SP L R SW Models other than KRF-V5010 KRF-V5010 Selecting VIDEO 2/MONITOR Depending on the component connected to the VIDEO 2/MONITOR jacks, select either the "VIDEO 2" setting or the "MONITOR" setting, as appropriate. 8