Jenn-Air JBBFX22NMX Owners Manual - Page 10

Refrigerator Installation Preparation, x 4

Get Jenn-Air JBBFX22NMX PDF manuals and user guides View all Jenn-Air JBBFX22NMX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

When Moving Your Refrigerator: Your refrigerator is heavy. When moving the refrigerator for cleaning or service, be sure to cover the floor with cardboard or hardboard to avoid floor damage. Always pull the refrigerator straight out when moving it. Do not wiggle or "walk" the refrigerator when trying to move it, as floor damage could occur. Clean Before Using After you remove all of the packaging materials, clean the inside of your refrigerator before using it. See the cleaning instructions in "Refrigerator Care." Important information to know about glass shelves and covers: Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. Tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use both hands when removing them to avoid dropping. Refrigerator Installation Preparation Before installing the refrigerator into cabinet, follow the steps given below: 1. Press fit the insulation tape on the side of refrigerator as shown in figure. Also attach 4 bracket caps on the door hinges. IMPORTANT: Cabinet wall thickness should be less than 20 mm to fit the caps properly. 2. Loosen the 4 screws of the bracket by rotating counterclockwise with the help of screw driver. Pull the bracket 3 mm up and then tighten the screws to fix it. = ~3mm = ~3mm x 4 ~3mm 3. Attach the 4 brackets on the sides of the refrigerator by using Philip screws. x 4 20mm

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
10
When Moving Your Refrigerator:
Your refrigerator is heavy. When moving the refrigerator for
cleaning or service, be sure to cover the floor with cardboard or
hardboard to avoid floor damage. Always pull the refrigerator
straight out when moving it. Do not wiggle or “walk” the
refrigerator when trying to move it, as floor damage could occur.
Clean Before Using
After you remove all of the packaging materials, clean the inside
of your refrigerator before using it. See the cleaning instructions in
“Refrigerator Care.”
Important information to know about glass shelves and
covers:
Do not clean glass shelves or covers with warm water when they
are cold. Shelves and covers may break if exposed to sudden
temperature changes or impact, such as bumping. Tempered
glass is designed to shatter into many small, pebble-size pieces.
This is normal. Glass shelves and covers are heavy. Use both
hands when removing them to avoid dropping.
Refrigerator Installation Preparation
Before installing the refrigerator into cabinet, follow the steps
given below:
1.
Press fit the insulation tape on the side of refrigerator as
shown in figure.
Also attach 4 bracket caps on the door hinges.
IMPORTANT:
Cabinet wall thickness should be less than
20 mm to fit the caps properly.
20mm
<20mm
2.
Loosen the 4 screws of the bracket by rotating
counterclockwise with the help of screw driver. Pull the
bracket 3 mm up and then tighten the screws to fix it.
~3mm
~3mm
~3mm
=
=
x 4
3.
Attach the 4 brackets on the sides of the refrigerator by using
Philip screws.
x 4
4.
Pass the wiring from the hole which is present on the backside
of the cabinet.