Intel BOXDH61SA Product Specification - Page 48

Reset Switch Header, 2.2.4.3, Power LED Header, Table 23., States for a One-Color Power LED

Get Intel BOXDH61SA PDF manuals and user guides View all Intel BOXDH61SA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

Intel Desktop Board DH61SA Technical Product Specification 2.2.2.4.2 Reset Switch Header Pins 5 and 7 can be connected to a momentary single pole, single throw (SPST) type switch that is normally open. When the switch is closed, the board resets and runs the POST. 2.2.2.4.3 Power LED Header Pins 2 and 4 can be connected to a one- or two-color LED. Table 23 shows the default states for this LED. More options are available through BIOS setup. Table 23. States for a One-Color Power LED LED State Description Off Steady Lit Blink Power off/sleeping Running Standby 2.2.2.4.4 Power Switch Header Pins 6 and 8 can be connected to a front panel momentary-contact power switch. The switch must pull the SW_ON# pin to ground for at least 50 ms to signal the power supply to switch on or off. (The time requirement is due to internal debounce circuitry on the board.) At least two seconds must pass before the power supply will recognize another on/off signal. 48

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
Intel Desktop Board DH61SA Technical Product Specification
48
2.2.2.4.2
Reset Switch Header
Pins 5 and 7 can be connected to a momentary single pole, single throw (SPST) type
switch that is normally open.
When the switch is closed, the board resets and runs the
POST.
2.2.2.4.3
Power LED Header
Pins 2 and 4 can be connected to a one- or two-color LED.
Table 23 shows the default
states for this LED.
More options are available through BIOS setup.
Table 23.
States for a One-Color Power LED
LED State
Description
Off
Power off/sleeping
Steady Lit
Running
Blink
Standby
2.2.2.4.4
Power Switch Header
Pins 6 and 8 can be connected to a front panel momentary-contact power switch.
The
switch must pull the SW_ON# pin to ground for at least 50 ms to signal the power
supply to switch on or off.
(The time requirement is due to internal debounce circuitry
on the board.)
At least two seconds must pass before the power supply will recognize
another on/off signal.