Intel BOXD915PBLL Product Specification - Page 27

Serial Ports, Parallel Port, Diskette Drive Controller, Keyboard and Mouse Interface

Get Intel BOXD915PBLL - Desktop Board D915PBLL PDF manuals and user guides
UPC - 675900579255
View all Intel BOXD915PBLL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Product Description 1.8.1 Serial Ports The Desktop Board can support up to two serial port connectors. Serial port A is located on the back panel. Serial port B (optional) is accessible using a connector on the component side of board. The serial ports support data transfers at speeds up to 115.2 kbits/sec with BIOS support. For information about The location of the serial port A connector The location of the serial port B connector The signal names of the serial port B connector Refer to Figure 15, page 58 Figure 16, page 60 Table 20, page 62 1.8.2 Parallel Port The 25-pin D-Sub parallel port connector is located on the back panel. Use the BIOS Setup program to set the parallel port mode. For information about The location of the parallel port connector Refer to Figure 15, page 58 1.8.3 Diskette Drive Controller The I/O controller supports one diskette drive. Use the BIOS Setup program to configure the diskette drive interface. For information about The location of the diskette drive connector Refer to Figure 16, page 60 1.8.4 Keyboard and Mouse Interface PS/2 keyboard and mouse connectors are located on the back panel.  NOTE The keyboard is supported in the bottom PS/2 connector and the mouse is supported in the top PS/2 connector. Power to the computer should be turned off before a keyboard or mouse is connected or disconnected. For information about The location of the keyboard and mouse connectors Refer to Figure 15, page 58 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
Product Description
27
1.8.1
Serial Ports
The Desktop Board can support up to two serial port connectors.
Serial port A is located on the
back panel.
Serial port B (optional) is accessible using a connector on the component side of
board.
The serial ports support data transfers at speeds up to 115.2 kbits/sec with BIOS support.
For information about
Refer to
The location of the serial port A connector
Figure 15, page 58
The location of the serial port B connector
Figure 16, page 60
The signal names of the serial port B connector
Table 20, page 62
1.8.2
Parallel Port
The 25-pin D-Sub parallel port connector is located on the back panel.
Use the BIOS Setup
program to set the parallel port mode.
For information about
Refer to
The location of the parallel port connector
Figure 15, page 58
1.8.3
Diskette Drive Controller
The I/O controller supports one diskette drive.
Use the BIOS Setup program to configure the
diskette drive interface.
For information about
Refer to
The location of the diskette drive connector
Figure 16, page 60
1.8.4
Keyboard and Mouse Interface
PS/2 keyboard and mouse connectors are located on the back panel.
±
NOTE
The keyboard is supported in the bottom PS/2 connector and the mouse is supported in the top
PS/2 connector.
Power to the computer should be turned off before a keyboard or mouse is
connected or disconnected.
For information about
Refer to
The location of the keyboard and mouse connectors
Figure 15, page 58